Bedienungsanleitung Dremel 8300 (Seite 12 von 96) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Schwedisch, Norwegisch, Finnisch)

488593

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

IMPORTANT! Practice on scrap material first to see how the

tool’s high-speed action performs. Keep in mind that your tool

will perform best by allowing the speed, along with the correct

accessory, do the work for you. Be careful not to apply too much

pressure.

Instead, lower the oscillating accessory lightly to the work

surface and allow it to touch the point at which you want to

begin. Concentrate on guiding the tool over the work using very

little pressure from your hand. Allow the accessory to do the

work.

Usually it is better to make a series of passes with the tool

rather than to do the entire job with one pass. To make a cut, for

example, pass the tool back and forth over the work. Cut a little

material on each pass until you reach the desired depth.

Slide "ON/OFF" switch

The tool is switched "ON" by the slide switch located on the

topside of the motor housing (Picture 7).

TO TURN THE TOOL "ON", slide the switch button forward.

TO TURN THE TOOL "OFF", slide the switch button backward.

Electronic monitoring

Your tool is equipped with an internal electronic monitoring

system that provides a “soft start”, which will reduce the

stresses that occur from a high torque start.

Variable speed slide switch

Your tool is equipped with a variable speed slide switch. The

speed may be adjusted during operation by sliding the switch

back or forth between any one of the settings.

To achieve the best results when working with different

materials, set the variable speed control to suit the job (See

Speed Chart, Picture 10) . To select the right speed for the

accessory in use, practice with scrap material first.

The speed of the cordless oscillating tool is controlled by setting

this slide switch on the housing.

PICTURE 10 Speed Chart, see Front Matter.

Addendum below:

Accessory Application

MM11

Sanding surfaces close to edges, in corners

or hard to reach areas.

Depending on the sanding sheet for, e.g.,

sanding wood, paint, varnish, thinset and

cement.

MM70W

For detail sanding.

MM70P

For sanding primer and removing brush

strokes, drops of paint and paint run.

WOOD

1/4

3/4

1/2

MM411

Smaller cuts and flush cuts.

Example: Cut-outs in furniture for cable

connections.

Accessory Application

MM470

Cutting and deep flush cuts; also for sawing

close to edges, in corners and hard to reach

areas.

Example: Flush cutting door jamb or window

sill, for flooring or tile installation.

MM422

Smaller cuts and plunge cuts.

Example: Sawing off water pipes (copper)

or cable ducts flush against walls, floors

or ceilings.

WOOD

MM450

Cutting in existing trim or flooring. Cutting

close to edges in corners or hard to reach

areas. Examples: Installing floor vent or

repairing damaged wood flooring.

MM500/MM501

Removing grout from between wall or floor

tiles.

Example: Removing grout joints between

wall tiles for repair work.

MM600

Remove vinyl flooring and bonded carpeting.

Example: On stairs/steps or other small/

medium sized surfaces.

Scraping off old coats of varnish/paint or

other adhesive.

MM610

Removing caulk, coats of peeling paint or

soft adhesive.

MM900

Removing thinset or cement.

Example: Grinding away thinset after tile

removal. Removing paint or oil stains from

cement.

PICTURE 7

A. Battery level indicator

B. Variable speed slide switch

Switch Setting Speed Range/min (OPM)

10 18 000 – 21 000

– 13 000 – 16 000

6 10 000 – 13 000

– 7 000 – 10 000

2 5 000 – 7 000

– 3 000 – 5 000

Battery level indicator

This tool is equipped with a battery level indicator that tells

you how much charge your battery has. A fully charged battery

is indicated when all three LED lights are illuminated. As the

battery discharges, the lights will turn off one by one until only

one light is on. When the last light starts "flashing", the battery

is almost empty.

When the battery becomes close to empty, the tool may shut

down automatically more frequent than normal. If this happens,

it is time to recharge the battery.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dremel 8300 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info