Bedienungsanleitung Dremel Trio (Seite 12 von 80) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Schwedisch, Norwegisch, Finnisch)

488596

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

GETTING STARTED

The Dremel Trio Tool is intended for cutting wood, plastic, thin

sheet metal, drywall, ﬁberboard, and wall tile using the applicable

tools and accessories recommended by Dremel.

This tool also sands using a variety of sanding drums and routes

using 4.8mm shank router bits. Make certain that the collet nut is

securely tightened before turning the tool on.

USE

ARTICULATION BUTTON

Your tool features a 2 position articulating head. To adjust,

depress articulation button and move head to desired position

(Fig. 2 or 3).

The articulation position is recommended for standard operations

on a ﬂat surface while in the 90° position (Fig. 2).

WARNING

Make sure articulation button clicks

back out to lock the handle before

turning the tool on.

WARNING

Make sure the pivoting handle is

securely locked in the desired position.

Operation when not secured properly may result in

unexpected movement of the pivoting handle and could

cause injury.

WARNING

Clamp the work piece in case it does

not remain stationary from its own

weight.

DUST EXTRACTION

Your tool is equipped with a dust port (G) for dust extraction. To

use this feature, insert dust port adapter (H) into dust port, attach

vacuum cleaner into the adapter (Fig. 4).

DEPTH ADJUSTMENT

Loosen the depth adjustment thumb screw (F) (counter-clockwise)

to change the depth of cut. Slide the base plate to the desired

depth of cut (about 3.2mm greater than material thickness when

cutting completely through something) and re-tighten the thumb

screw (clockwise) (Fig. 5).

The maximum recommended depth of cut is 13mm of wood.

When using sanding drums and router bits it is recommended to

make less aggressive more frequent passes through the material

to extend the tool and accessory life.

TRIGGER “ON-OFF” SWITCH

To turn tool “ON”, squeeze the trigger switch. To turn the tool

“OFF”, release the trigger switch which is spring loaded and will

return to “OFF” position automatically (Fig. 6).

"LOCK-ON" BUTTON

The "Lock-ON" button, located in the handle of your tool allows

for continuous operation without holding the trigger (Fig. 6).

• TO LOCK TRIGGER "ON": squeeze trigger, depress "Lock-ON"

button and release trigger.

• TO UNLOCK THE TRIGGER: squeeze trigger and release it

without depressing the "Lock-ON" button.

OVER CURRENT PROTECTION

Your tool is equipped with over current protection that will slow

the motor automatically when overstressed. When this occurs you

should reduce cutting pressure, rate of cut. The tool will increase

speed again for maximum cutting performance.

VARIABLE SPEED DIAL

Your tool is equipped with a variable speed dial. The speed may

be adjusted during operation by presetting the dial on or between

any one of the settings (Fig. 7).

INSERTING BITS (Fig 8)

1. Depress and hold the shaft-lock button (L) in and rotate the

collet nut (K) and shaft until the shaft-lock engages and holds

the shaft.

2. Use the standard equipment wrench (N) to loosen nut

(counter-clockwise).

3. Remove the old bit insert the new bit as far in as possible.

4. Re-engage the shaft-lock and tighten the nut (clockwise) by

hand and then with the wrench until bit is held securely.

NOTE: Be sure to read the instructions supplied with your Dremel

accessory for further information on its use.

NOTE: Use only Dremel TRIO, ø4.8 mm shank accessories (Fig 9).

SPEED SETTINGS

* Speed for light cuts; Caution - burning on deep grooves.

* Depending on cutting direction relative to grain.

• For maximum control use a slow feed rate of cut.

• For maximum control place a second hand on the front of the

tool or on the rear of the foot.

• For straightest possible cut use straight edge guide or fence.

• When using a fence, position it on the left side of the foot.

• When using a straight edge guide, position it on the right

side of tool.

• When cutting most materials steer the tool in a clock-wise

direction. Exception: when tracing an outlet steer counter

clock-wise, an exception to this rule is when cutting around

an outlet box.

SETTINGS FOR APPROXIMATE REVOLUTIONS (Fig. 9)

Switch Setting Speed Range

2 10000-12000 RPM

4 12000-14000 RPM

6 14000-16000 RPM

8 16000-18000 RPM

10 18000-20000 RPM

PROPER GUIDING (Fig. 10)

• Keep in mind that router bit turns clockwise

• Guide tool so that bit turns into the work piece, not away

from it.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dremel Trio Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info