801302
16
Zoom out
Zoom in
Vorherige Seite
1/48
Nächste Seite
16
Instructions for use ROTEC
Drive Medical GmbH & Co. KG | As per: 28.04.2021 | Errors and alterations excepted
EN
456
Never swivel the footrests inwards!
Length and angle adjustment
of the footrest
Length adjustment
(photo 7)
Use the enclosed Allen
wrench to loosen the
screw on the footrest and
adjust the length as desi-
red by shifting up or down.
Retighten the screw!
Angle adjustment
(photo 8)
Use the enclosed Allen
wrench to release the
screw on the footrest until
it can be pulled out of the
toothed wheel inwards.
Now rotate the footrest
into the desired position
and press it back into the
toothed wheel.
Retighten the screw!
Adjusting seat height (rear wheel mount)
The height of the seat at
the rear can be adjusted
in increments. To adjust
it, remove both hand rim
wheels by pressing the re-
lease button (see section
Attach wheels”). Unscrew
the nut of the wheel mount
and move it into the desi-
red hole.
Replace the nut with the
locking washer and tigh-
ten it (photo 9).
Ensure that the wheel axle is properly tightened!
Adjusting seat height (front wheel mount)
The height of the seat can be adjusted in increments and
is correspondingly adjusted in the desired inclination
of the seat surface. To adjust, unscrew the wheel axle
screw and pull it out.
The plugs of the corres-
ponding holes can be ea-
sily exchanged. Now move
the wheel in the desired
position and reinsert the
wheel axle screw and tigh-
ten it (photo 10).
Ensure that the wheel
axle is properly tightened!
Adjusting the height of the backrest
The height of the backrest
can be adjusted in incre-
ments.
Note: When the backrest
is adjusted, the height of
the push handles is also
automatically adjusted.
To adjust the backrest,
remove the left and right
nuts under the guide tube
of the backrest (photo 11).
Pull the screws out. Now adjust the desired height by
pulling or pushing on the respective push handle.
Reinsert the screws, put on the knurled nuts and tighten
them.
Always ensure that both sides are adjusted identically.
16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Drive Rotec wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info