Bedienungsanleitung DRU BASSO-01 (Seite 21 von 28) (Englisch, Holländisch, Französisch)

810304

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

give you the information you need to install the appliance

in such a way that it will operate properly and safely.

If the installation instruction is not clear, national/local

regulations must be observed.

• NB: To ensure the ignition works properly, the ignition

wire must come into as little contact as possible with

the metal parts of the heater and should therefore

not be wound round the gas or pilot-light pipes or the

thermocouple.

• When installing the appliance, check the air circulation

(by convection) around the thermostat sensor. If there

is a lack of air circulation, the sensor must be moved

to a position with sufficient air circulation for correct

operation of the appliance.

Positioning the appliance

• The appliance should only be installed in a well ventilated

room, to ensure there will always be sufficient air supply.

• The appliance may not be installed against a wall of

combustible material unless the wall is protected with an

insulation panel.

• The connection between the pipe mouth and the flue

should be as short and straight as possible and the gas

control block easily accessible.

• The minimum distance between the back of the appliance

and the wall is 70 mm.

Connecting to the flue

• Have the chimney professionally cleaned before

connecting the appliance. Although the heater will still

work with only a very slight draught, we recommend that

the chimney be inspected for obstructions etc. annually.

• The internal diameter of the pipe mouth is 101 mm.

• The height of the pipe mouth is variable (max. 690mm,

min. 450 mm)

• Saw the plate for the outlet to the required length, as

shown in fig 3.

• Fix the outlet to the baffle using the mounting strips.

• TThe connection between the pipe mouth and the flue

duct should be made using corrosion-proof material.

• The connecting pipe should never be lower than the

heater pipe mouth.

• Fit a longer connecting pipe from the pipe mouth to the

flue sloping (2%) towards the pipe mouth.

Fitting the aluminium protective plate

The plate should be fitted under the foot of the interior

during installation. Slide the plate backwards until the front

is level with the front of the foremost adjustable feet.

Connecting to the gas supply

Use an approved connecting tap with coupling in the

supply pipe (for Belgium this must be B.G.V. approved).

In addition:

• Expel the air from the supply pipes before connecting

the appliance.

• Avoid pressure on the gas control block and the pipes.

• Check all connections for gas tightness.

Positioning the logs

• Open the glass window by unscrewing the two M6

socket-head screws on the right-hand side, using the

spanner provided.

• Place the tray around the burner (fig. 4a).

• Fill the burner with vermiculite (this is in the plastic bag

with the log set). Spread it evenly over the burner tray

and the surrounding tray. Do not put any vermiculite

higher than the edge of the tray. Save the remaining

vermiculite in case you lose any later during cleaning or

maintenance.

Position the logs as follows:

• Lay the large log (A) against the back wall, on the log

supports, with the yellow side down and the knot towards

the left.

• Lay the front logs (B and C) with the bark facing up, as

illustrated in fig. 4b.

• If appliciable and required, distribute the glow material

over the burner(s).

• Now lay the rest of the logs (D, E, F, G and H) in place as

illustrated in fig. 4b.

• Close the window again with the two socket-head screws.

The logs should not be laid in any other way as this could

cause the formation of soot. Neither should the logs

touch pilot light burner.

You can “play” with the flames by moving the vermiculite,

glow material and chips about on the burner bed until you

have created the desired flame effect.

Do not use any materials other than those supplied.

The supplied materials are incombustible and have been

manufactured specifically for this appliance.

English

INSTRUCTIONS FOR INSTALLATION

38C-2098

fig. 4a

Basso-01

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DRU BASSO-01 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info