Bedienungsanleitung DRU GLOBAL 70 XT (Seite 46 von 60) (Englisch, Holländisch)

528138

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

USER MANUAL

manual control of the remote control (see ﬁ g. 2).

In addition, the remote control can also be used to set a

number of additional functions:

- temperature display in degrees Celsius or Fahrenheit;

- time;

- thermostat function;

- timer for thermostat function.

Although highly improbable, we cannot

rule out that your appliance’s ignition

process can be started unintentionally

through other remote controls.

This could be the remote control of your

neighbours' gas heater, but also car keys

and garage door openers.

The result will be that your appliance will

burn when you do not want it to.

Unintended ignition of your appliance could be solved/pre-

vented by:

- setting a new communication code between remote con-

trol and receiver (see section 4.2.1);

- when left unattended for a longer period, set button A on

the gas control to the position MAN (see section 4.2.2.1);

- close the gas tap near your appliance. This is the safest

precaution, if the appliance will not be used for a longer

period;

- Observe stated precautions / safety instructions - even if

the appliance is not in use.

4.2.1 Setting the communication code

Prior to putting the application into operation, a communi-

cation code must be set between the remote control and

the receiver. The code is chosen randomly from the 65000

available codes. As a result, the chance that other remote

controls near you are using the same code and affect the

operation of your appliance is very small.

Follow the procedure described below:

• Hold down the reset button on the receiver, until you

hear two consecutive sound signals (see ﬁ g. 3).

• After the second, longer signal, let go of the reset button.

• Press button

(small ﬂ ame) or button (large ﬂ ame) on

the remote control within 20 seconds, until you hear an

extra long sound signal: this is the conﬁ rmation of a

correct communication.

!Caution When installing a new remote control or

receiver, you must set a new communica-

tion code.

4.2.2 MAN position

By brieﬂ y pressing the SET button, you will go through the

following functions:

MAN  ✹ TEMP   TEMP  (P*)TIMER  MAN

where, depending on the timer setting:

(P*) is displayed as P1 ✹, P1 , P2 ✹, P2 

!Tip You can also go back to the MAN position

by pressing the button

(large ﬂ ame) or

(small ﬂ ame).

!Caution - When pressing the buttons (with the ex-

ception of the SET button), the transmis-

sion symbol ( ) will appear to indicate

that transmission is taking place between

the remote control and the receiver;

- The receiver acknowledges the transmis-

sion with a sound signal;

- The appliance will automatically enter the

standby position, if there is no transmis-

sion for 6 hours.

• Set the remote control to the MAN position.

4.2.2.1 Ignition

- During the ignition process, you are not

allowed to operate control button B on

the gas control manually (see ﬁ g. 4);

- Always wait 5 minutes after the pilot

burner has gone out, before you re-ignite

the appliance;

- Close the gas tap in case of malfunctions

and/or poor operation and warn the

installer.

Caution

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DRU GLOBAL 70 XT Seite 46

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DRU GLOBAL 70 XT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info