Bedienungsanleitung DRU GLOBAL 70 (Seite 36 von 60) (Englisch, Holländisch)

528137

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

INSTALLATION MANUAL

!Caution Use the placement brackets as indicated

in the ﬁ gures.

• Fill the tray surrounding the burner with chips; equally

spread the chips; see ﬁ g. 13j.

• Finally place log D, the left log; see ﬁ g. 13k.

6.10. Pane

After placing the wood set you can place the pane, as

described below.

!Caution - Avoid damages when removing/placing

the pane;

- Use the socket spanner supplied for loo-

sening/tightening the self-tapping screws.

6.10.1 Removing the pane

Remove the pane in accordance with the following instruc-

tions (see ﬁ g. 14a up to 14n):

• Remove the vertical decorative strip at the left and right

side by pushing the strip upwards with a screwdriver,

tilting the strip parallel to the pane and then removing it.

• Remove the self-tapping screw (used for fastening the

pane) from the right glass strip.

• Unscrew the 3 self-tapping screws from the upper glass

strip.

• Remove the upper glass strip.

• Unscrew the self-tapping screw of the wedge at the left

and right side with 2 strokes.

!Caution Do not fully remove the self-tapping

screw, but let it remain in the wedge.

• Push the wedge (left and right) as far upwards as possible.

• Then retighten the self-tapping screws.

• Take hold of the handles and pull the pane towards you.

• Slide the pane as far to the left as possible.

• Tilt the pane towards you by using the right handle and

remove the pane.

6.10.2 Placing the pane

The pane is ﬁ tted by using the above procedure, in reverse

order.

!Caution - Avoid/remove ﬁ ngerprints on the pane,

since otherwise they will burn into the

surface;

- The self-tapping screws must not be

over-tightened, since otherwise they could

break or strip the thread: tight=tight;

- When tightening, push the wedge down-

ward.

7. Wireless remote control

The appliance is supplied with a wireless remote control.

Ignition, controlling the ﬂ ame height and switching off are

performed by a remote control that operates a receiver in

the control box.

User Manual, chapter 4, Wireless Remote Control,

describes the operation of the appliance including the way

the remote control works.

Do not ignite the appliance until it is fully

installed.

Below, we will describe how the receiver is connected.

7.1 Receiver

The receiver should be connected to the appliance, before the

batteries are installed.

Follow the procedure below (see ﬁ g. 15):

• Fit the connection cable’s brown plug to the receiver

(see ﬁ g. 15, arrow F).

• Connect the white plug to the gas control.

!Tip The plugs have different sizes that

correspond with the connectors.

• Connect the cables of thermocouple 1 to the receiver;

(see ﬁ g. 15, arrows B).

!Tip - The size of the eye corresponds with the

size of the screw;

- The colours of eye and screw also

correspond.

• Connect the black wire with the white plug of

thermocouple 2 to the receiver (see ﬁ g. 15, arrow E).

!Caution - Make sure that the wires of

thermocouple 2 cannot come into contact

with hot parts;

- Make sure the ignition cable cannot come

into contact with other wires.

• Connect the ignition cable to the receiver;

(see ﬁ g. 15, arrow A).

• Connect power:

a) When using batteries, see section 7.1.1 below;

b) When using an adapter:

- connect it to the receiver; (see ﬁ g. 15, arrow C);

- insert the plug into the wall socket.

• Place the receiver (V) in the control box, as indicated on

ﬁ g. 16.

• Bend the antenna out of the clips; see ﬁ g. 15, arrow D.

• Set the antenna straight.

!Caution - Do not place the antenna (N) too close to

the ignition cable and/or metal parts (for

the correct position, see ﬁ g. 16);

- Do not place the ignition cable over and/or

along metal parts: this will weaken the spark;

- Do not lay the ignition cable over the recei-

ver: this could damage the receiver;

- Avoid dust on or in the receiver: cover it

when performing work.

Caution

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DRU GLOBAL 70 Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DRU GLOBAL 70

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info