Bedienungsanleitung DRU Maestro 75 Tunnel (Seite 35 von 56) (Englisch)

810253

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

Installation manual

1Identify logs A to K (see fig. 8-9).

2- Use the burn stains on the logs for identification.

- In the overview photograph, the side glass pane is located on the right side.

1Place log A over the lying burner in the positioning brackets (see fig. 8-20).

1Place log B on the left side behind log A, in the two positioning brackets and on log A.

1Place log C on the right side behind log A, in the positioning bracket and on log A, make sure there is 1 centimetre play

between log C and the standing burner to the right (see fig. 8-20).

1Place log D in the positioning bracket to the right and on log C.

1Place log E against the tube of the standing burner to the right and in the positioning bracket.

1Place logs F and G in front of the lying burner, in the positioning brackets.

1Place log H against the tube of the standing burner to the left and in the positioning bracket.

1For appliances without LEDs, use all chips in the wood set.

1Fill the vermiculite plates with chips, spread the chips evenly, keep the sections marked in red free of chips (see fig. 8-18).

1For appliances with LEDs, use the glow rocks, coals and a portion of the chips.

1Only use 400ml of the supplied grey chips and 800ml of the black chips. This is less than the total ammount supplied with

the appliance. Dispose of the surplus chips according to local laws.

2First place the glow rocks and then the coals. Switch on the glow lighting while placing, so that the stray light can be

seen directly and covered with the rocks and coals.

1Spread the glow rocks over the grid pattern and square holes in the vermiculite plate, keep the sections marked in red

free (see fig. 8-19).

1Spread the chips over the remaining sections, keep the sections marked in red free.

LED appliances have a different type of base covering to appliances without LEDs.

3- The vermiculite plates are provided with square holes, which ensure air supply. Do not place more than one layer of

base covering over these holes.

- Ensure that the base covering does not enter the slot for the glass pane.

2Place chips on the edge of he pane frame. Prevent chips from getting under the pane frame (see fig. 8-17).

1Place log I on the left side in front of log A, in the positioning bracket and on log A.

Make sure there is 1 centimetre play between log I and the standing burner to the left (see fig. 8-23).

1Place log J over the standing burner to the left, make sure the recess falls over the burner properly.

1Place log K over the standing burner to the right, make sure the recess falls over the burner properly.

2Spread the ash over the chips and/or place the glow material over the lying burner in separate tufts.

3- Prevent the ash from ending up on the burners.

- Only place the glow material on sections that are marked green.

- The areas around the ionization and ignition should remain free from glow material (see fig. 8-15).

- The glow material may affect the colour of the flame picture.

8-14

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DRU Maestro 75 Tunnel Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DRU Maestro 75 Tunnel

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info