Bedienungsanleitung Dual DTFT 27-2 (Seite 122 von 131) (Deutsch, Englisch, Französisch, Italienisch)

494579

122

Zoom out

Zoom in

Vorherige Seite

1/131

Nächste Seite

- 21 -

Sleep Timer Indicator

It is displayed on the upper right of the

screen when a new programme is entered

by digit button or by pressing “P<P”, “-P/CH”,

“P/CH+”, “ ”, “ ” or “ ” button. If sleep

timer is activated it is displayed with the TV

status and erased with it after 3 seconds.

In last minute, sleep timer indicator is dis-

played on the upper right of screen and

stays there until the TV goes automatically

to stand-by.

0:15

Mute Indicator

It is placed in the upper middle of the screen

when enabled, and it stays there until it is

disabled.

To cancel mute, there are two alternatives;

the first one is pressing to "

" button, this

volume is set to the preceding value, and the

second one is increasing the volume level,

thus it starts at the minimum level to in-

crease. By decreasing the volume level in

mute state, mute will not be ignored, only the

volume level will decrease. If mute is can-

celled after decreasing the volume level, the

volume will be valid with the decreased

level.

No-Signal Detection (TV)

If no valid signal detected, it takes 5 minutes

for the switching to the Stand-By mode un-

less any signal detected or no any Remote

Control command is accessed.

After a Remote Control command (if No-Sig-

nal Timer is active) the timer stops and if no

signal detected again the timer is initialized

to 5 minutes and starts 3 seconds later

again to count down.

It is not valid in AV mode.

4:31

No-Signal Detection (PC)

If no valid signal detected for 5 minutes sys-

tem goes to Stand-By mode. To switch on

the system press “

” button.

As the last status feature, system starts from

TV or PC, whichever was the status before

stand-by or switch-off. Note that SCART in-

puts have the precedence on both TV and

PC.

Volume Bar

It is displayed in the lower middle of the

screen. When a volume command is re-

ceived (pressing “

+” or “ -” by Re-

mote Control or Control panel at the top of

the TV) and no menu is active, it stays on the

screen for 3 seconds, after the last volume

command or until another command is re-

ceived in between.

AV Modes

By pressing the “ “ button you can switch

your TV to AV modes (except being in Tele-

text). Pressing this button consecutively will

switch the TV in one of the optional AV

modes: AV-1, AV-2, AV-3, S-VIDEO, PC.

In order to quit the AV mode press the “

”,

digit buttons or “-P/CH” or “P/CH+” .

Signal Out Of Range

When the PC input signal is not supported

by LCD-TFT TV, a message is displayed like

“Signal out of range” and screen is blanked.

If no valid signal detected for 5 minutes sys-

tem goes to Stand-By mode.

ENG-2707W-1543 UK-27 INCH TFT (17MB08)-DUVAR MON-(WO PIP)(CHI MEI-B1).p65 30.05.2006, 16:3621

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dual DTFT 27-2 Seite 122

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info