Bedienungsanleitung Dual Saw CS 490 (Seite 23 von 80) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Türkisch)

578050

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

and the area around the collar using grease remover and wipe all parts dry or clean the areas with

compressed air.

• The bottom protective lid should only be retracted to make special cuts by hand, for instance bag cuts

and compound cuts. Lift the bottom protective lid with the handle on the protective lid only. As soon as

the saw blade enters the material, the bottom protective lid needs to be released in order to permit the

further sawing work. The bottom protective lid should move automatically.

• Ensure that the bottom protective lid covers the saw blade when you store the blade. If the still rotating,

unprotected saw blade comes into contact with a hard surface, the saw moves suddenly and cuts all

objects with which it comes into contact. Remember that it takes some time before the saw blade stops

once the switch has been let go.

• NEVER place the material you are sawing over your leg and do not hold it in your hand when sawing.

The material must be placed on a solid surface in order to avoid injuries, the saw blade from getting

jammed or uncontrolled movements.

• Always hold the tool on the isolated handles when you carry out work during which the saw could come

into contact with covered wires or the own power cable. In the event of contact with a live wire, the open

metal parts of the tool are also live, which means that the operator may suffer an electric shock.

• EXCLUSIVELY use DUALSAW saw blades developed speciﬁcally for this tool. Other saw blades do not

suit the installation device precisely and may result in the user losing control of the saw.

• Never use damaged ﬂange or screws or such that do not ﬁt precisely. The ﬂange and screws were

designed in such a way that optimal services and safe operation of the saw are ensured.

• Do NOT switch the saw on while you are carrying it. The bottom protective lid may open when coming

into contact with clothing. Accidental contact with the rotating saw blade may result in severe injuries.

• Never attempt to use the saw with only one saw blade. This results in a recoil of the saw in the directi-

on of the user, which may cause severe injuries.

HOW TO AVOID A RECOIL

• A recoil occurs when a saw blade is jammed, gets stuck or no longer moves smoothly. The recoil re-

sults in the saw suddenly jumping out of the workpiece in the direction of the user.

• If the saw blade is jammed or gets stuck in the cut, the saw blade can no longer

• rotate and the saw is hurled back into the direction of the user by the motor movement. Recoils occur

when the tool is wrongly used, the operating instructions are ignored or inappropriate conditions exist

at the workstation. Recoils can be avoided by taking the below precautions:

• Hold the saw ﬁrmly with both hands and ensure that you are prepared for recoils by standing ﬁrmly and

positioning your arms accordingly. Suitable precautions can allow the user to absorb recoils.

• When processing large plates, it must be ensured that they are placed ﬁrmly in several locations to

avoid the risk of the saw blade jamming and of recoils. Large plates may sag in the middle due to their

weight. On both sides of the plate, along the cut line and at the edge of the plate, racks need to be

placed to prevent any sagging.

• Do not use blunt or damaged saw blades. Blunt or wrongly set saw blades result in a narrow cut groove

and increased friction. This may cause the saw blade to jam, resulting in recoils.

• Proceed with particular caution when making a bag cut in existing walls or covered areas. The protru-

ding saw blade may saw objects which may cause a recoil.

• Depending on use, the switch may need to be replaced during the life cycle of the saw. If the switch

fails in the OFF position, it may not be possible to start the saw any longer. If it no longer works while

the saw runs, the saw can no longer be switched off using the button. Immediately disconnect the

power cable of the saw from the mains adapter in such cases and do not use the saw again until it has

been repaired. Contact customer services.

• Prepare for a recoil when the saw blade starts to jam or when the saw blocks and moves quickly in the

direction of the operator. Let go off the switch immediately in this case. Do not exert excessive power.

Proceed with caution and in a controlled manner.

WARNING!

• Do NOT lose your attention simply because you are familiar with the saw. Remember

that already a fraction of a second is sufﬁcient to cause severe injuries.

• This saw is ﬁtted with special saw blades. Saw blades of another type may be used under cer-

tain circumstances. The use of other saw blades is not safe and may cause severe injuries.

• If the saw blades come into contact with the workpiece before the full operating speed is rea-

ched, the saw may recoil, can cause severe injuries.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dual Saw CS 490 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info