Bedienungsanleitung Durkopp Adler 527 (Seite 7 von 34) (Englisch)

613283

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

6. Operation of the machine

Caution!

Do not use this sewing machine without using the finger guard

(C, Fig. 4) and without the take-up lever guard (P, Fig. 2).

6.1 Upper thread threading (Fig. 1, 2)

Caution!

Before starting the threading operation, switch off the

main switch and put off the feet from the pedals on the

stand to avoid the starting of the machine by treading

the pedal.

After having inserted the bobbin with thread on the thread stand (N), unwind

the thread in sufficient length and pass it through the holes in the thread stand

(N). Direct it then through the thread guide (A) and through the guide (B) - with

the machines without any thread cutter, or through the auxiliary thread tensioner

(L) with the machines provided with such thread cutter. Feed the thread between

the dishes of the tensioner (C). Direct the thread through the adjusting spring

(D) around the guide (E) and through the guide (F) and (G) into the take-up lever

eye (H). From here the thread is directed downward through the guides (F) and

(J) and through the hole of the thread guide (K) on the needle bar towards the

needle eye. Thread the thread into the needle eye from the front (from the sewer)

rearward.

6.2 Winding of thread on the hook bobbin (Fig. 3)

From the thread stand the thread is directed to the tensioner (A) through the

guide (B) on the machine head. From the guide the thread is directed on the

hook bobbin mounted on the shaft (C) of the winder. Wind up the thread

end several times on the bobbin in the clockwise direction and feed it towards

the spring (D). Introduce the thread between the coils thereof and, when

pulling it slightly, cut it with the knife which is mounted inside the spring.

Engage the winder by means of the lever (E). After having wound up the

thread on the bobbin, the winder stops automatically. After having removed

the bobbin from the winder shaft it is possible to cut the thread with the

knife protected by the spring (D) or to cut it with scissors. The thread (A)

serves for regulating the tension of the thread for winding.

6.3 Needle insertion (Fig. 4)

Caution!

Before starting the operation of the needle change, switch off

the main switch and put the feet off the pedals on the stand to

avoid the machine start by treading the pedal.

After having chosen the correct needle thickness (number) corresponding

to the system of the prescribed type (usually the system 134), loosen the

screw (A) in the needle holder and insert the needle (B) up to the bottom of

the hole in the needle holder. Turn it in such a way, so that its long groove is

directed ahead (towards the sewer).

Caution - when choosing a thicker needle it is necessary to check, whether

the hook beak does not catch the needle - the eventual setting of the hook

position is to be carried out by a qualified person. Check up, whether the

needle passes through the centre of the needle hole, change a faulty needle.

Fig. 1

Fig. 2

Fig. 4

Fig. 3

OFF ON

MAIN SWITCH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Durkopp Adler 527 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Durkopp Adler 527

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info