613275
85
Zoom out
Zoom in
Vorherige Seite
1/98
Nächste Seite
1
8.8.2 Application messages
Pictogram Description Category Reaction/ troubleshooting
Capacity counter is zero
Note
· Clamping foot can only be lowered
after pressing OK
.
· The message disappears when
it has been confirmed.
· When the message has been confirmed
the capacity counter is reset to its
initial value.
Hand wheel turned
manually
Warning
After the sewing procedure is interrupted:
· no further sewing is possible
· Cancel the sewing procedure by
moving the pedal backwards, confirm with
manual switch 1 (clamps) or
press ESC on the
control panel.
Contour exceeds the
internal clamping foot
frame in the -X or +X
direction.
Warning
· no further sewing is possible
. select another c lamping foot
· select another sewing pattern
· Reduce the X offset in the appropriate
direction
.
Contour exceeds the
internal clamping foot
frame in the -X or +X and
Y direction.
Warning
· no further sewing is possible
. select another c lamping foot
. select another sewing pattern
·
Reduce
the X offset in the appropriate direction.
Reduce the sewing patter n in the Y direction.
Contour exceeds the
internal clamping foot
frame in the -X and -Y and
+Y direction.
Warning
· no further sewing is possible
. select another c lamping foot
. select another sewing pattern
. Reduce X offset
·
Reduce the X offset in the appropriate direction.
Contour exceeds the
internal clamping foot
frame in the +X and -Y or
+Y direction.
Warning
· no further sewing is possible
. select another c lamping foot
. select another sewing pattern
. Reduce X offset
. Reduce
the Y offset in the appropriate direction.
Contour exceeds the
internal clamping foot
frame in the X and -Y or +Y
direction.
Warning
· no further sewing is possible
. select another c lamping foot
. select another sewing pattern
. Reduce the sewing pattern in the X direction
. Reduce
the Y offset in the appropriate direction.
Contour exceeds the
internal clamping foot
frame in the -Y or +Y
direction.
Warning
· no further sewing is possible
. select another c lamping foot
. select another sewing pattern
.Reduce
the Y offset in the appropriate direction.
83
85

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

durkopp-adler-531

Suche zurücksetzen

  • Wie stellt man die Geschwindigkeit der nähmaschine adler 531 ein? Eingereicht am 23-1-2018 19:57

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Durkopp Adler 531 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Durkopp Adler 531

Durkopp Adler 531 Bedienungsanleitung - Deutsch - 98 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info