613275
89
Zoom out
Zoom in
Vorherige Seite
1/98
Nächste Seite
Error Description Possible cause Troubleshooting
code
4312 Unknown dongle type - Dongle not correctly
formatted
- Dongle faulty
- Format the dongle again
- Use another dongle
4530
-
4537
4900
Menu system error/
user error message
Internal error
- Switch machine off and on again
- Update software
- Inform DA service
5101 NV RAM empty Control unit is new. No data
available
Control unit for a different
machine class, data
incompatible
Data is reset to factory settings
5104 NV RAM checksum
error
NV SRAM faulty
Malfunction
- Check with Multi-test, check
control unit
- Switch the machine off and
on again
- Data is reset to factory settings
5804 Free contours:
Checksum incorrect
-NVSRAMfaulty
- Malfunction
- Check with Multi-test, check
control unit
- Switch machine off and on
again.
Data is reset to
factory settings
5808 Error - free seam
contour stitch number
cannot be determined
Internal error
- Switch the machine off and
on again
- Update software
- Contact DA Service
5809 Free contours:
Maximum number of
partial contours
Maximum number of partial
contours (interim cutting)
exceeded
Delete the interim cutting
operations in the free contours
5810 Free contours:
Minimum number of
stitches per partial
contour
Minimum number of stitches
per partial contour not adhered
to
Move interim cutting operations in
the free seam contours.
5900 Sequence error -
Impermissible
sequence number
Internal error
- Switch the machine off and on
again.
-Update software
- Contact DA Service
6152
-
6154
6204
Input/ output error Internal error
- Switch the machine off and
on again
- Update software
- Contact DA Service
6351
-
6354
Error I
2
C Control unit faulty Check control unit
6551
6554
6651
6751
-
6759
Upperpartposition
error/ AD converter/
processorerror/step
motor driv er
Internal error
- Switch the machine off and on
again.
-Update software
- Contact DA Service
7460 Test interface
communication
-Cablefault
- Test interface cable
faulty
- Internal error
- Switch off source of interference
- Check cable
- Switch the machine off and on
again
87
1
89

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

durkopp-adler-531

Suche zurücksetzen

  • Wie stellt man die Geschwindigkeit der nähmaschine adler 531 ein? Eingereicht am 23-1-2018 19:57

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Durkopp Adler 531 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Durkopp Adler 531

Durkopp Adler 531 Bedienungsanleitung - Deutsch - 98 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info