Bedienungsanleitung Duux DXHU13 Beam Mini (Seite 6 von 42) (Deutsch, Englisch, Holländisch, Französisch, Spanisch)

773969

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

Mode button

Use the button to active/deactivate the auto mode

or set a timer.

Press the button to cycle through the modes:

Auto mode and Timer mode.

The selected mode icon will illuminate on the display.

Use the and buttons to change the setting. To

conrm the changes, wait for ± 3 seconds or press

the button again.

Note: If the display shows , the chosen

mode won’t activate or will be deactivated after

conrmation.

For more information on functions, see chapter

Functions.

/ Increase/decrease button

The behaviour of the increase / decrease buttons

depends on the mode that is being set.

• Manual mode: Increase or decrease mist output

level.

• Auto mode: Increase or decrease the desired

relative humidity level.

• Timer mode: Increase or decrease the timer

with 1 hour increments.

Functions

Manual mode

In Manual mode users can select the desired mist

output.

Use the and buttons to select the desired

mist output. The mist output level bars will change

accordingly. There are three mist output levels:

Low

Medium

High

Auto mode

In Auto mode users can set the built-in hygrostat

to their desired relative humidity level. If the ambient

relative humidity drops below the desired level, the

mist output will automatically turn on. It will continue

to operate in the chosen mist output level until the

hygrostat level is reached.

Before turning on Auto mode, select the desired

mist output level in Manual mode using the and

buttons. Press the button until the indicator

illuminates on the display. Press the and

buttons to set the hygrostat to the desired relative

humidity level.

Note: The mist output level can’t be changed when

the mode is active.

The desired relative humidity level can be set between

40% and 90% with increments of 5%. When you go

below 40% or above 90%, the display will show

and Auto mode will be deactivated. The following

sequence shows the steps and how they cycle.

> 40% > 45% > 50% > [...] > 90% > >40%

Timer

Press the button until the indicator illuminates

on the display. Use the and buttons to

increase or decrease the timer hours in the following

sequence: 1h > 2h > 4h > 8h > OFF.

Once the timer is activated, the device will

automatically shut down after the set timer has been

completed.

Display brightness

The display will automatically dim after the last touch

or press.

Rell water indicator

When the water level becomes too low to produce

mist, the device will make three “beep”-sounds

and the display will show the red indicator in

combination with an E1 notication. Please follow the

steps explained in Filling the water tank. When the

water tank is relled you may plug in the power cord

and turn on the device.

Display notications

The following notication may show on the display:

• E1: The water level in the mist chamber is too

low to produce mist.

• E2: The water tank is not placed on the

humidier base .

• E3: If this notication shows, please contact your

nearest service provider.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Duux DXHU13 Beam Mini Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info