Bedienungsanleitung Dyson AB12 - Airblade V (Seite 15 von 64) (Alle Sprachen)

761230

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

L N

6mm

L N

6mm

3.1

Rear cable entry.

4 5

Connecting to terminal block. Attaching main body.

Warning: Risk of electric shock!

Ensure power is not connected.

1. Ensure the cable does not sit above

the cable guide from the cable inlet

to the terminal block. If the cable

sits above the guide walls it may

interfere with main components,

prevent the security screws being

fitted correctly, or risk the main body

being forced on to the backplate,

causing damage.

2. Unscrew the cable clamp from

the backplate. Remove the cable

terminal block.

3. Open the flap on the terminal

block. Secure the live, neutral and

earth wires into the correct terminal

locations as indicated on the

terminal block casing.

4. Verify the connections are correct

before proceeding.

5. Close the flap on the terminal block

and fit it into the backplate.

6. Screw in and secure the cable clamp.

CAUTION: DO NOT OVERTIGHTEN

AND CRUSH THE POWER CABLE.

CAUTION: Do not overtighten screws.

1. Hook the main body of the unit over

the top rim of the backplate.

2. Swing the main body of the unit

down on to the back plate. (For

installations with the cable entry on

the side, ensure that the side bracket

seal is correctly seated against the

main body.)

3. Insert and tighten the (2) security

screws into the side of the main body

with the service tool as illustrated.

Recommended torque of 0.5-

0.7NM.

4. Turn power on.

5. Test unit for correct operation.

IMPORTANT

DO NOT USE SEALANT WHEN

FIXING THE UNIT TO THE WALL.

DO NOT PAINT/COAT THE MAIN

BODY OR PLACE GRAPHICAL

STICKERS ON IT OR THIS MAY

DAMAGE THE ANTI-BACTERIAL

SURFACE.

IF A CLEANING PRODUCT IS LEFT

ON THE MACHINE FOR TOO LONG,

A FILM WILL FORM. THIS MAY

REDUCE THE EFFECTIVENESS OF THE

ANTI-BACTERIAL SURFACES.

electricity supply cable from the wall

must align with rear cable entry point

in the backplate.

4. Mark the location on the wall with a

pencil. Use the backplate to mark the

locations for the four fixing points.

5. Drill holes.

6. Fix the optional back panel if

required.

Fixing the backplate to the wall.

Fit the backplate securely to the wall

using the appropriate fixings for the

wall type and weight of the unit. Do

not use counter-sunk screws.

Do not secure tightly until after the

power cable has been secured.

Installing the power cable.

1. Cut the entry hole in the rubber

cable grommet to the correct size:

leave a hole smaller than the

diameter of the power cable to

ensure the cable fits tightly.

2. Pull the cable through the

grommet. Ensure the cable is long

enough to route correctly through

the backplate to the terminal

block.

The cable must sit in the

dedicated channel.

3. Fit the grommet into the

backplate. Ensure it is secure.

4. Secure the screws in the

backplate.

5. Proceed with step 4, ‘Connecting

to terminal’.

6mm

● Primary fixing locations (x4).

Do not use countersunk screws.

●Secondary fixing locations.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dyson AB12 - Airblade V Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Dyson AB12 - Airblade V

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info