Bedienungsanleitung Dyson Airblade Wash and Dry WD05 (Seite 2 von 160) (Alle Sprachen)

761232

Zoom out

Zoom in

Vorherige Seite

1/160

Nächste Seite

ROI

LOOKING AFTER YOUR HAND DRYER

WARNING

This product is not to be used in sinks where a plug is fitted. Before engaging the water

flow ensure that the plughole is clear of any obstructions and that water can drain freely.

HOW TO USE

Place your hands beneath the Dyson hand dryer and it will automatically, creating sheets of air

to scrape water from your hands.

For best dry time results:

• Keep your hands flat and parallel to the appliance surface, approximately 5 mm from the

blade, drawing your hands through the airflow from your wrists to finger tips.

• Move your hands slowly through the airflow keeping a consistent speed, approx. 2.5 seconds

per side, alternating between front and back each time.

• Keep you hands flat, close the gaps between your fingers and keep your thumbs in to ensure

that the whole of your hand is drawn through the airflow.

TROUBLESHOOTING GUIDE

WARNING: RISK OF ELECTRIC SHOCK!

Problem Action

The hand dryer fails to start. Check that the fuse/circuit breaker is working

and that the power is connected. Must be

performed by a qualified electrician.

Ensure that the cleaning cap is removed and

that the sensors are clean and unobstructed.

If a safe method of switching is available,

turn the unit on and off. If a safe method is

not available, a qualified electrician must

perform this task.

The hand dryer is turning on and

off erratically. Ensure that the sensors are clean and free

from obstructions.

Check that the sensor cable from the tap is

securely connected. Must be performed by a

qualified electrician.

The hand dryer sometimes cuts out when

in use but resumes operation after a period

of time.

Check that the air inlet is clean and free

of dust.

Remove any dust from the air inlet.

Ensure that the air inlet is free from

obstructions and has sufficient clearance

(see installation instructions).

The dry time of the hand dryer has increased. Inspect the inlet grille for dust and remove.

Inspect the filter and change if required.

Ensure that the hose is securely attached to

the base of the tap and no leaks are present.

Must be performed by a qualified electrician.

NOTE: Ensure water feed is completely flushed of debris, copper filings etc. prior to

connecting to the product. Failure to do so will damage the solenoid valve.

The instructions in this manual and the installation guide must be followed completely,

as failure to do so may result in incorrect operation, damage to property and/or

personal injury. It is recommended that an isolation valve is fitted with this product

during installation. Dyson will not be held liable for any damage to property or

personal injury, or any loss of business or revenue, if you, your staff, your installer

or service engineers have not followed the instructions given in this manual and the

installation guide.

27.11.2017 12:51 - C92757_WD04_OPMAN_INT_X588-OWNERS-MANUAL-PART 3- TEXT.indd_15_0c2s_15_0c2s

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dyson Airblade Wash and Dry WD05 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Dyson Airblade Wash and Dry WD05

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info