Bedienungsanleitung Dyson Airblade Wash and Dry WD06 (Seite 154 von 160) (Alle Sprachen)

761231

154

Zoom out

Zoom in

Vorherige Seite

1/160

Nächste Seite

154

LOOKING AFTER YOUR HAND DRYER

WARNING

This product is not to be used in sinks where a plug is fitted. Before engaging the water

flow ensure that the plughole is clear of any obstructions and that water can drain freely.

HOW TO USE

Place your hands beneath the center of the tap and water will flow automatically for as long as

the hands remain in place.

For best dry time results:

• Place your hands to either side of the center tap to activate the hand dryer, creating sheets of

air to scrape water from your hands.

• Move your hands backwards and forwards slowly through the air, turning them over so both

back and front are exposed to the airflow.

• Keep you hands flat, close the gaps between your fingers and keep your thumbs in to ensure

that the whole of your hand is drawn through the airflow.

TROUBLESHOOTING GUIDE

WARNING: RISK OF ELECTRIC SHOCK!

Problem Action

The hand dryer fails to start. Check fuse/circuit breaker is working

and that the power is connected. Must be

performed by a qualified electrician.

Ensure the cleaning cap is removed and that

the sensors are clean and unobstructed.

If a safe method of switching is available,

turn the unit on and off. If a safe method is

not available, a qualified electrician must

perform this task.

The hand dryer is turning on and

off erratically. Ensure sensors are clean and free

from obstructions.

Check that the sensor cable from the tap is

securely connected. Must be performed by a

qualified electrician.

The hand dryer sometimes cuts out when

in use but resumes operation after a period

of time.

Check the air inlet is clean and free of dust.

Remove any dust from the air inlet.

Ensure that the air inlet is free from

obstructions and has sufficient clearance (see

installation instructions).

The dry time of the hand dryer has increased. Inspect the inlet grille for dust and remove.

Inspect filter and change if required.

Ensure that the hose is securely attached to

the base of the tap and no leaks are present.

Must be performed by a qualified electrician.

USES

NOTE: Ensure that the water feed is completely flushed of debris, copper filings etc.

prior to connecting to the product. Failure to do so will damage the solenoid valve.

The instructions in this manual and the installation guide must be followed completely,

as failure to do so may result in incorrect operation, damage to property and/or

personal injury. It is recommended that an isolation valve is fitted with this product

during installation. Dyson will not be held liable for any damage to property or

personal injury, or any loss of business or revenue, if you, your staff, your installer

or service technician have not followed the instructions given in this manual and the

installation guide.

27.11.2017 12:51 - C92757_WD04_OPMAN_INT_X588-OWNERS-MANUAL-PART 3- TEXT.indd_15_0c2s_15_0c2s

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dyson Airblade Wash and Dry WD06 Seite 154

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Dyson Airblade Wash and Dry WD06

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info