Bedienungsanleitung Dyson AM10 (Seite 15 von 20) (Englisch)

669052

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Using your humidifier

Please read the ‘Important Safety Instructions’ in this Dyson Operating

Manual before proceeding.

Introduction

• This is a cool mist, ultrasonic type of humidifier. Moist air is

directed into the room from the loop amplifier.

• Water passes over a UV-C emitter to ensure that it is 99.9%

bacteria-free before misting commences.

Location

• Always place the appliance on a firm, flat, level surface.

• Do not place the appliance on a rug, carpet, wooden flooring,

or any other surface that may be damaged by exposure to water

or moisture.

• It is recommended that a waterproof mat or pad is placed under

the appliance.

• Do not place the appliance underneath overhanging surfaces.

• Do not place the appliance in an area where it is accessible

to children.

• Store the appliance indoors. Do not use or store it below

5°C (41°F). Ensure the appliance is at room temperature

before operating.

• For the best performance, place on the floor, in the corner of

the room, at least 1m from any wall and facing into the centre of

the room.

Operation

• All parts must be securely fitted before use.

• Do not use the appliance unless it has been cleaned according

to instructions.

• In humidifier mode do not use without water in the tank.

• Do not lubricate any part of this appliance.

• When switched on, a small blue LED on the back of the appliance

lights up to show that power is being received by the appliance.

(Note: It does not mean that the appliance itself is operating.)

• Once the water treatment cycle completes the appliance is ready

to begin humidification.

Setting humidity level

• On first use, the display will show ‘70%’, which is the highest

relative humidity setting. The fan will run on lowest airspeed, ‘01’.

For each use after this the appliance will remember the last target

humidity level and airflow speed set.

• The appliance will not operate unless the target humidity setting is

above the current room humidity level.

• The appliance will automatically adjust to avoid

excessive humidity.

• Mist will be visible only in certain conditions (impacted by light,

background colour, etc.) or at the lowest settings.

Automatic Mode

• Press the AUTO button on the remote. This is the recommended

mode of operation.

• The appliance selects a comfortable humidity for the room, based

on environmental factors such as current humidity level and

air temperature.

• When the room reaches the appropriate humidity level the

appliance will switch itself ‘ON’ or ‘OFF’ as necessary to maintain

that level. The fan will remain running when the target humidity

has been reached.

Manual mode

• Select the desired humidity level (from 30% to 70%). When the

room reaches the target humidity level the appliance will switch

itself ‘ON’ or ‘OFF’ as necessary to maintain that level. The fan

will remain running when the target humidity has been reached.

Fan mode

• The fan mode button on the remote control turns the humidifier

mode ‘OFF’. Control the fan mode using the airflow and

timer buttons.

• No water is needed for the fan mode.

Control without the remote

• Press the power button on the appliance to turn ON/OFF.

• Press and hold the power button on the appliance to adjust the

humidity setting.

• Fan mode and the sleep timer cannot be operated without the

remote control.

• The air speed setting automatically sets to '05'.

Refilling

• When refilling, empty the tank completely (preferably washing

and drying it), then refill – this keeps the water fresh.

• With a full tank of cold tap water (3 litres) the appliance will run

for at least 10 hours, depending on the target humidity setting

and other environmental conditions. Do not add anything to the

water ( such as scents, oils etc).

Cleaning the base

• Small water spillages may occur. While the amount of water in

the trough is not significant enough to damage the appliance,

significant care should be taken when emptying it. Ensure that

water does not enter through the inlets of the appliance. If some

water does pass through the inlets, dry the exterior with a cloth

and continue to use as normal.

Cleaning the tank

• Pour in the recommended citric acid solution. Replace the cap

and shake tank for 30 seconds. Then leave to stand. After 15

minutes, empty the tank. Rinse and wipe over all surfaces. Repeat

if necessary.

Storage

• When not in use, unplug from the mains electricity supply.

• Store the appliance in a dry location and arrange the cable away

from traffic areas so that it will not be tripped over or damaged.

• Clean the appliance and tank as instructed before storing and

before re-use.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dyson AM10 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Dyson AM10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info