Bedienungsanleitung Dyson Ball (Seite 9 von 16) (Englisch)

702345

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

• Some carpets may fuzz if a rotating brush bar is used when

vacuuming. If this happens, we recommend vacuuming

with the brush bar switched 'OFF' and consulting with the

carpet manufacturer.

• The brush bar on the appliance may damage some carpet types. If

you are unsure, turn ‘OFF’ the brush bar.

• Check the brush bar regularly and clear away any debris (such as

hair). Debris left on the brush bar may cause damage to flooring

when vacuuming.

Looking after your Dyson appliance

• Do not carry out any maintenance or repair work other than

that shown in this Dyson Operating Manual, or advised by the

Dyson Helpline.

• Only use parts recommended by Dyson. If you do not this could

invalidate your guarantee.

• Store the appliance indoors. Do not use or store it below

3°C (37.4°F). Ensure the appliance is at room temperature

before operating.

• Clean the appliance only with a dry cloth. Do not use any

lubricants, cleaning agents, polishes or air fresheners on any part of

the appliance.

• If used in a garage, always wipe the base plate and ball with a dry

cloth after vacuuming to clean off any sand, dirt or pebbles that

could damage delicate floors.

Vacuuming

• Do not use without the clear bin and filters in place.

• Fine dirt such as flour should only be vacuumed in very

small amounts.

• Do not use the appliance to pick up sharp hard objects, small toys,

pins, paper clips, etc. They may damage the appliance.

• When vacuuming, certain carpets may generate small static charges

in the clear bin or wand. These are harmless and are not associated

with the mains electricity supply. To minimize any effect from this

small static charge, do not put your hand or insert any object into the

clear bin unless you have emptied it first, then cleaned it with a damp

cloth (see ‘Cleaning the clear bin’).

• Do not put the appliance on chairs, tables, etc.

• Before vacuuming highly polished floors, such as wood or lino, first

check that the underside of the floor tool and its brushes are free

from foreign objects that could cause marking.

• Do not leave the cleaner head in one place on delicate floors.

Emptying the clear bin

• Empty as soon as the dirt reaches the level of the MAX mark – do

not overfill.

• Switch ‘OFF’ and unplug before emptying the clear bin.

• To remove the cyclone and clear bin unit, press down on the red

button on the top of the carrying handle on the cyclone.

• To release the dirt, press all the way down on the same red button on

the top of the carrying handle on the cyclone.

• To minimise dust/allergen contact when emptying, encase the

clear bin tightly in a plastic bag and empty.

• Remove the clear bin carefully from the bag.

• Seal the bag tightly, dispose as normal.

• To refit:

– Ensure the airway in the bin base is clear of dust and dirt.

– Close the clear bin base so it clicks into place.

– Push the cyclone and clear bin unit into the main body of the

appliance; it will click into place.

– Ensure the cyclone and clear bin unit is secure.

Cleaning the clear bin

• Before cleaning the clear bin, follow 'Emptying the clear bin'

instructions.

• To remove the cyclone unit from the clear bin press the red bin

release button. This exposes a small silver button behind the opening

mechanism. Press the silver button and separate the cyclone unit

from the clear bin.

• Do not use detergents, polishes or air fresheners to clean the

clear bin.

• Do not put the clear bin in a dishwasher.

• Do not immerse the cyclone in water or pour water into the cyclones.

• Clean the cyclone shroud with a damp cloth only.

• Ensure the clear bin is completely dry before replacing.

Washing your filters

• Your appliance has two washable filters, located as shown on the

front page.

• Check and wash the filters regularly according to instructions to

maintain performance.

• Switch ‘OFF’ and unplug before checking or removing the filters.

• The filters may require more frequent washing if vacuuming fine dust

or carpet cleaning powders.

• Wash with cold water only. Do not use detergents.

• Do not put the filters in a dishwasher, washing machine, tumble

dryer, oven, microwave or near a naked flame.

Filter A

• Remove the cyclone and clear bin (see ‘Emptying the clear bin’).

• Release the catch on the front of the cyclone handle and then remove

the filter.

• Wash the filter with cold water only. Hold under a tap and run water

through the open end until the water runs clear. Turn upside down

and tap out.

• Run water over the outside of the filter until the water runs clear.

• Squeeze and twist with both hands to make sure the excess water

is removed.

• Stand the filter on its wide, open end to dry. Leave to dry completely

for a minimum of 24 hours.

• Replace the filter into the cyclone. Swing the handle back into place.

Ensure the latch clicks to engage and is secure. Fit the cyclone and

clear bin unit onto the appliance (instructions above).

Filter B

Filter B is a two part filter; an inner foam ring and an outer filter

and shell.

• Lay the appliance on its side.

• To remove filter B:

– Turn the blue central locking dial on the outer cover of the ball

anti-clockwise until the cover is released.

– Lift off the ball shell cover.

– Turn the outer filter one-quarter anti-clockwise to release.

• Separate the inner foam ring from the outer filter and shell. Wash

both the inner and outer filter with cold water only. No hot water and

no detergents.

• The outer filter and shell should be rinsed on all sides and tapped

out until the water runs clear, then tapped out again to ensure

all excess water is removed. (Tap on the plastic rim, not the filter

material.) Leave to dry completely for a minimum of 24 hours.

• Run water over the inner foam ring until the water runs clear.

• Leave the filter to dry completely for a minimum of 24 hours.

• It is normal for the filter in the ball to turn grey in colour.

• To refit filter B:

– Refit the inner foam ring onto the outer filter and shell.

– Refit the outer filter on to the ball.

– Secure the filter by turning it clockwise so the arrows align.

• When refitting the outer cover of the ball, keep turning the central

locking dial clockwise. It is locked once it starts to click.

Blockages – thermal cut-out

• This appliance is fitted with an automatically resetting thermal

cut-out.

• Large items may block the tools or wand inlet. If any part becomes

blocked the appliance may overheat and automatically cut-out.

• If this happens, follow the instructions in ‘Looking for blockages’.

• NOTE: Large items may block the tools or wand inlet. If this happens,

do not operate the wand release catch. Switch ‘OFF’ and unplug.

Failure to do so could result in personal injury.

Dyson Ball Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Dyson Ball

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info