Bedienungsanleitung EasyAlarm CONTROL (Seite 4 von 32) (Englisch)

515345

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

2. SAFETY INSTRUCTIONS

2.1 Approval

Declaration of Conformity

According to the R&TTE Directive 1999/5/EC of 09.March 1999

Manufacturer’s Name: Leitronic AG

Manufacturer’s Address: Engeloostrasse 16

CH-5621 Zufikon, Switzerland

declares that the product

Product Name: EasyAlarm

Model Number: EA-8-EXT

conforms to the following product specifications:

Safety (R&TTE, Article 3.1a): EN60950: 1992+A1+A2+A3+A4

EMC (R&TTE, Article 3.1b): EN 50081-1, 1992

EN 50082-1, 1997 Class B

Telephone: CTR21 as specified in Council Decision 98/482/EC

Supplementary Information

The product herewith complies with the requirements of the following Directives and carries the CE marking accordingly:

the EMC directive 89/336/EWG

the Low Voltage Directive 93/68/EEC

Zufikon, 1. April 2008 Silvan Tognella

2.2 Telephone connection

EasyAlarm® is designed to connect to an analogue telephone line. This connection should remain in service after a mains

power. These are:

 analogue PSTN

 analogue port of an ISDN terminal (ISDN-NT has to be reprogrammed for emergency operation at the ab-port)

 analogue port of a private exchange using UPS (Uninterruptible power supply 1h buffering)

 GSM Interface with approval, i.e. EA-GSM-Interface from Leitronic.

Not suitable:

 Voip or cable modem, as in case of power loss it is not functional!

The voltage of the telephone network is defined in EN 41003. It is higher than 40 V and therefore please beware for

electrical hazard and disconnect

2.3 Power supply

A transformer according to the safety regulation EN60950 provides power supply. 9V battery is used as a back up in case

of power failure. It is located on the rear side oft the device.

2.4 Safety notes

 Do not bring the device into contact with a liquid (water).

 Do not open the device (exception: opening of battery compartment).

 Replace the 9V-battery as soon as the announcement “battery error” is announced.

 Please note: The telephone cord must be disconnected before opening the battery compartment because

otherwise you can get in contact with the telecommunication voltage!

 Check alarm functions and start a test-call, before the system is put in service.

 In case that EasyAlarm® is used to monitor children, the supervising person must be in a suitable distance to

take immediate care for the child. EasyAlarm® does not replace personal supervision!

 The same applies to handicapped persons, EasyAlarm® is not a substitute of a personal care taker!

 An alarm by telephone is only successful if the alarmed party takes care of the following points:

 Alarm must not be answered by an answering machine or equal equipment

 Mobile phones can be out of range (e.g. underground car park, shielded rooms, remote areas..)

 Take care of the charging condition of the mobile phone

 Loud noise can prevent you from hearing the ringer

 All the electrical connections have to be potential free. Observe the regulation according to EN60950.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

EasyAlarm CONTROL Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von EasyAlarm CONTROL

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info