Bedienungsanleitung EasyAlarm CONTROL (Seite 7 von 32) (Englisch)

515345

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Select user language / record individual message  Details according to section 6.3

12. Slide function switch to PROG

13. Enter *. *. #.

 Current individual message will be announced followed by “to modify press * , to stop press # “

14. Select language for user announcements: (facultative)

Press key 1 to 4 to select user languages: 1 for German, 2 for French, 3 for English GB, 4 for Italian

15. Press * and start speaking

16. Press # to finish recording, max. duration is 12 seconds

 New individual message will be announced. You can repeat steps 14 to 16 until text is fine!

17. Slide function switch to OFF

Program PIN-code  Details according to section 6.4

18. Slide function switch to PROG

19. Press key #.

 You can prevent the alarm unit from unintended re-programming by pressing * ..

20. Enter PIN-code (4 to 7 digits)

21. Press key #.

22. Re-enter PIN-code for confirmation

23. Press key #.

 New PIN-code will be announced

24. Slide function switch to OFF

Alarm unit is now ready for operation  Details according to section 7

25. Slide selection switch to the requested position (I/II/III)

4.1.4 Activation of motion sensor

Provided the motion detector is plugged in, EasyAlarm® detects the motion detector during the switching on procedure.

Important notes:

 By disconnecting the motion detector during the operation mode, an alarm is

triggered followed by the announcement: ”alarm due to sensor 1, sensor failure!”

 By connecting the motion detector after the start up procedure of the alarm unit,

an alarm is triggered followed by the announcement: “alarm due to sensor 1,

sensor 1 activated!”

4.1.5 Deactivation of motion sensor

If the motion detector is not plugged in, EasyAlarm® automatically deactivates the

supervision of the motion detector.

4.1.6 Adjustment

Safety note:

 Before you open cover please check, that the telephone cord is DISONNECTED.

Otherwise you can get in contact with the telecommunication voltage!

Remove the front cover by twisting a flat screwdriver in the slot between the cover and

the base at the bottom of the motion detector

4.1.6.1 Pulse count

You can set PULSE jumper at position 1,2 or 3 corresponding to the desired pulse count

before an alarm will be triggered. Default = 2.

4.1.6.2 WALK-test

To disable LED indication, remove the LED jumper and place it on one pin only. To

activate LED indication, place LED jumper over both pins.

4.1.6.2.1 Mounting height

If motion detector is not mounted at 2.5m you can adjust like this:

1. Loosen the PC-Board holding screw. Slide the PC-Board so that the plastic pointer

on the right side is positioned at the appropriate scale position.

 For higher than 2.5m => Slide PC-Board up

 For lower than 2.5m => Slide PC-Board down

2. Tighten the PC-Board holding screw

3. Mount front cover

4. Walk through the entire protected area and observe the LED to ensure full coverage

Mounting screw

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

EasyAlarm CONTROL Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von EasyAlarm CONTROL

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info