Bedienungsanleitung EasyAlarm CONTROL (Seite 28 von 32) (Englisch)

515345

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

11. ACCESSORIES

Further accessories can be found on our homepage on www.easyalarm.ch.

11.1Motion / Presence detector-PIR-RJ45 (Plug&Protect)

11.1.1 Preliminary considerations

Choose the mounting location after careful consideration of the area to be protected.

The motion detector should be located so that an intruder will cross the infrared beam

pattern. If used to verify presence, a regular used room should be detected. Figure

shows the different infrared beam patterns at a typical mounting height of 2.5m.

Notes:

 Do not mount detector towards direct sunlight or near to heat sources.

 Do not mount detector behind items like glass or curtains because the infrared-

beam cannot penetrate them.

 Keep away pets like cats or dogs from the protected area.

 Do not protect the same area by more then one detector, because they can interfere.

11.1.2 Installation

Connect the cable of the motion detector on the EXT port of the alarm unit. The AC adapter of the alarm unit provides the

power supply of the detector

11.1.3 Activation

Provided the motion detector is plugged in, EasyAlarm® detects the motion detector during the switching on procedure.

Important notes:

 By disconnecting the motion detector during the operation mode, an alarm is

triggered followed by the announcement: ”alarm due to sensor 1, sensor

failure!”

 By connecting the motion detector after the start up procedure of the alarm unit,

an alarm is triggered followed by the announcement: “alarm due to sensor 1,

sensor 1 activated!”

11.1.4 Deactivation

If the motion detector is not plugged in, EasyAlarm® automatically deactivates the

supervision of the motion detector.

11.1.5 Specification

Supply voltage 9..16 VDC (through AC-adapter)

Dimension 107 x 58 x 39 mm (L x W x D) without swivel

Weight 75 g

Cable length 8m (RJ45)

Detection type passive infrared (PIR)

Alarm contact normally closed

11.1.6 Adjustment

Safety note:

 Before you open cover please check, that the telephone cord is DISONNECTED.

Otherwise you can get in contact with the telecommunication voltage!

Remove the front cover by twisting a flat screwdriver in the slot between the cover and

the base at the bottom of the motion detector

11.1.6.1 Pulse count

You can set PULSE jumper at position 1,2 or 3 corresponding to the desired pulse count before an alarm will be triggered.

Default = 2.

11.1.6.2 WALK-test

To disable LED indication, remove the LED jumper and place it on one pin only. To activate LED indication, place LED

jumper over both pins.

11.1.6.2.1 Mounting height

If motion detector is not mounted at 2.5m you can adjust like this:

5. Loosen the PC-Board holding screw. Slide the PC-Board so that the plastic

pointer on the right side is positioned at the appropriate scale position.

 For higher than 2.5m => Slide PC-Board up

 For lower than 2.5m => Slide PC-Board down

6. Tighten the PC-Board holding screw

7. Mount front cover

8. Walk through the entire protected area and observe the LED to ensure full

coverage

Mounting screw

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

EasyAlarm CONTROL Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von EasyAlarm CONTROL

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info