Bedienungsanleitung Easymaxx F5M-A1E - Z04271 (Seite 4 von 8) (Deutsch, Englisch, Holländisch, Französisch)

703750

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

EN Instructions

Customer Service / Importer:

DS Produkte GmbH, Am Heisterbusch 1, 19258 Gallin, Germany •

✆ +49 38851 314650 *)

Calls to German landlines are subject to charges. The cost varies depending on the service provider.

Inserting Batteries

Four 1.5 V batteries of type C are required for battery mode.

1. Take off the battery compartment

cover on the bottom of the device:

Press the fastener on the battery

compartment cover and open up the

battery compartment cover.

2. Before inserting the batteries, check

whether the contacts in the battery

compartment

(8)

and on the batter-

ies are clean, and clean them if nec-

essary.

3. Insert four 1.5 V batteries, type C into the battery compartment.

Ensure the correct

polarity (+ / –).

4. Insert the battery compartment cover and ﬂ ip it shut until it can

be heard to engage in place.

Replace the batteries when the power of the device starts to wane.

PLEASE NOTE! Always replace all batteries together. Do not use

batteries of different types or brands, or batteries with different ca-

pacities.

Use

PLEASE NOTE

■ Do not connect the device to a computer because the high cur-

rents could damage the computer.

1. Place the device on a table or an-

other dry, even, and ﬁ rm base.

2. Take the cover

(1)

off the device (pull

it upwards).

3. Pull the water tank

(12)

out of the

device.

4. Pull the lamella insert

(11)

out of

the device, immerse it in cold water,

shake off any excess water and then

reinsert it with the arrow markings

ahead into the device. The frame of

the lamella insert must face the air

outlet openings.

5. Unscrew the valve

(13)

from the wa-

ter tank, ﬁ ll the water tank with cold

tap water and screw the valve ﬁ rmly

back onto the water tank.

6. Insert the water tank into the device.

Make sure when you do this that the

valve ﬁ ts correctly in the valve re-

ceptacle

(9)

7. Once batteries have been inserted in the device, it is ready for

operation. For mains power mode, plug the Micro B connector

of the USB cable into the USB socket (7) of the device and the

A connector into the socket of a USB mains adapter (not sup-

plied with the device). Connect the mains adapter to an easily

accessible socket.

8. To switch on the device, slide the switch

(3)

to position I for

cooling level 1 or position II for the higher cooling level 2. When

the device is switched on, the operating lamp

(4)

is lit.

On the back of the device warm air is sucked in, cooled by the

water in the device and emitted again at the front (as cool air).

9. To switch off the device, slide the switch to the middle posi-

tion 0. The operating lamp goes out.

10. If you are not using the device, pull the mains adapter out of the

plug socket and the USB cable out of the device.

Cleaning and Storage

• If necessary, wipe down the device with a slightly damp cloth.

• When not in use the device should be stored in a dry place

which is not accessible to children and animals.

Troubleshooting

If the device does not work properly, check whether you are able to

rectify the problem yourself. If the problem cannot be solved with

the steps that are listed, contact the customer service department.

Do not attempt to repair a defective electrical device

yourself!

If the device does not work, check the following:

• In mains power mode:

– Are the device, USB cable and mains adapter connected to

one another correctly?

– Is the mains adapter inserted in the plug socket correctly?

– Does the mains adapter correspond to the technical data of

the device?

– Is the plug socket defective? Try another socket.

– Check the fuse of the mains connection.

• In battery mode: Are no batteries inserted, or are the batteries

inserted incorrectly, or are they too weak?

• Is there water in the water tank

(12)

and is the lamella

insert

(11)

moist?

• Is the impeller

(10)

blocked?

Technical Data

Article number: 04271

Model number: F5M-A1E

Voltage: 6 V DC (4 x 1.5 V battery, type C) or

5 V DC (USB)

Power: 2.5 watts

Protection class: III

Air throughput: 6 dm

Air volume: < 6730 m³/h

Evaporation volume: < 50 ml/h depending on the cooling level

Water tank: 380 ml

Disposal

Dispose of the packaging material in an environmentally

friendly manner and take it to a recycling centre.

Dispose of the device in an environmentally friendly manner

at a recycling centre for used electrical and electronic devic-

es. More information is available from your local authorities.

Batteries should not be disposed of in the normal household

waste. They should be removed prior to disposal of the de-

vice and disposed of separately from the device at suitable

collection points.

Z 04271 M DS V1.1 0118

Article number: 04271

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Easymaxx F5M-A1E - Z04271 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info