Bedienungsanleitung EBERLE Instat 868-a8U (Seite 4 von 4) (Englisch)

458733

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

Table 1: If the radio link does not operate …...

Test as follows Yes NO

1 Receiver: is the round signal lamp on? Continue at 2 Check mains power supply, renew fuse inside receiver if necessary

2. Receiver: Is a channel (1...8) signal lamp flashing Duplicate address; see 4.7.1 or

Can the audible warning signal be heard?

(possibly only after 1 hour) Transmitter signal still missing; continue at 3 Continue at 5

3. Check active links: see 4.4

If the ‘learned’ channels come on? continue at 4 New learning procedure: see 4.1

4. Transmitter: is the battery OK? Continue at 5 Fit new batteries

5. Transmitter: set to 30 °C

Is the relay energised after 30 seconds (lamp comes on)? Continue at 6 No transmitter signal: continue at 7

6. Transmitter: Set to 5 °C

Is the relay switched off after approx. 30 seconds (lamp off)? Everything OK No transmitter signal: continue at 7

7. Transmitter - receiver - thermal actuator: check wiring,

if necessary Re-learn link with receiver

Can items 5 and 6 now be performed successfully? Everything OK (see 4.2 Radio link range test)

8. Reduce distance between transmitter and receiver If necessary, use the device Receiver may have a fault

to approx. 2 metres. with an additional antenna

Can items 5 and 6 now be performed successfully?

Room 1 Room 2 Room 3 Room 4 Room 5 Room 6 Room 7 Room 8

Valve

Function change over needed if thermal actuator normally open is used - see 4.8

Valve

Fig. 1 Single-room control with simple thermostat; 8 rooms,

each with separate thermostat control

Room 1 Room 2 Room 3 Room 4 Room 5

Valve

Function change over needed if thermal actuator normally open is used - see 4.8

Valve

Fig. 2 Single-room control; one transmitter supplies signals

on various channels (several valves for 1 room); 5 rooms, each

controlled by a thermostat. Room 1 = 6 valves; room 5 = 3 valves

Room 1 Room 2 Room 3

Room 5

Room 6 Room 7 Room 8

Valve

Function change over needed if thermal actuator normally open is used - see 4.8

Valve

Room 4

Fig. 3 Single-room control with master/slave system

8 rooms, each controlled by a thermostat. Rooms 1 … 3 comply with

the internal timer, rooms 4 … 8 comply with the master timer

program on channel 4.

Room 1 Room 2 Room 3 Room 4 Room 5 Room 6 Room 7

Valve

Function change over needed if thermal actuator normally open is used - see 4.8

Valve

Pump

Fig. 4 Pump logic – single-room control for 7 rooms,

channel 8 for pump logic Note: a valve cannot be connected to

channel 8 if the pump logic is used.

Pump

Rec. 1 Rec. 2

Pump

Rec. 1 Rec. 3

Rec. 2

Fig. 5 Pump logic with 2 rows of receivers

Fig. 6 Pump logic with 3 rows of receivers

N supplied from external source

Heat / Cool

signal for cooling,

e.g. from heat pump

Fig. 7 Heating/cooling changeover

Heat / Cool

signal from central changeover,

e.g. heat pump

Application diagram with 4 independent receivers

Fig. 8 Heating/cooling changeover

HYG

Hygrostat, e.g.

Hyg 6001, SSHyg

Fig. 9 Dew-point identification by hygrostat

Fig. 10 Dew-point identification

by specific dew-point sensor

TAU

Dew-point sensor =

TS 193 683

(max. 4 in parallel)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

EBERLE Instat 868-a8U Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von EBERLE Instat 868-a8U

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info