611868
7
Zoom out
Zoom in
Vorherige Seite
1/24
Nächste Seite
Transmitter - Micro Remote Control Module Ref : EMML
July 2009 page 7 EMML
PROGRAMMING
In order to add the Micro Transmitter to a different installation from
the original one, or to one with interference from a nearby system,
it is necessary to program a different code.
The programming address is made up of a ”HOUSE” code (from A through P) and
a “UNIT” code (from 1 through 16). The factory default address of the transmitter/
receiver pair is set at A1; proceed as follows to set a different code.
A. Accessing programming mode.
- Press the Micro Transmitters START (1) and STOP (0) buttons briey and
simultaneously. The LED turns YELLOW.
Then the LED lights up RED once (for the HOUSE CODE), then GREEN once (for
the UNIT code). The Micro Transmitter is in the A-1 setting.
You have 6 seconds to program a new code.
B. Setting the HOUSE CODE.
- Press the (1) button as many times as needed to get to the desired HOUSE
CODE and then release it.
Example: A = Press once, B = Press twice, C = Press three times, ... P = Press
16 times.
- After having set the HOUSE CODE, the LED will ash YELLOW 3 times to conrm
the code has been memorized and exit from programming mode.
C. Set the UNIT CODE.
- Repeat step A only.
- Press and release the (0) button as many times as needed to get to the desired
UNIT CODE and then release it.
Example: 1 = Press once, 2 = Press twice, 3 = Press 3 times... 16 = Press 16
times.
- After having set the UNIT code, the LED will ash YELLOW 3 times.
VERIFICATION
Let the Micro Transmitter be recognized by the receivers.
Verify On/Off switch operation.
You must wait about a second between each On / Off command.
When changing the battery, the registered code will be retained by the Micro
Transmitter.
Troubleshooting - please check FAQ and technical support on
www.ebodeelectronics.eu
7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Ebode EMML wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info