Bedienungsanleitung Ebode IR Link M (Seite 5 von 28) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

611759

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Version 1.0 - 8-1-2013 5 ebode IR Link M

your components.

Note: The IR Emitters have self-adhesive tape on the back. Use this to stick them onto the

IR eye of your equipment. This should be done very carefully and precisely. Test the

position of the IR Emitters first, before you finally stick them onto the eye.

Connect additional IRED Emitters to the corresponding jack of the Hub, and install the

small Emitters onto your controlled components as per the procedure above.

Tech Tip: By using a flashlight to shine on the display of your Audio/Video device, you can

easily see where to place the emitters.

Step 3: Run the wire of the IR Receiver through the back of your cabinet and plug the

jack into the correct socket of the Hub.

Step 4: Plug the power supply adapter into the little Hub power connection.

ATTENTION: If you are only using one appliance, then you do not need to use the

additional IR Emitters. Never remove it from the wire! Just dress up the wire and leave

close to the Hub.

TIP2: If you want to control more appliances, you can purchase an extra IR Emitters (IRED

series) and plug this into the other connection.

7. Operation

Point your original remote control at the IRLM Receiver. As soon as you press a button, the

Receiver captures the IR command, converts it into a low voltage signal, and transmits it

to the ebode IRHUB1. This unit converts the signal into an IR message back, in order to

control the selected A/V source.

8. How to avoid and solve possible problems

Although the ebode IR Link M is equipped with proprietary eIR

(pronounced Irex)

Technology, which guarantees a high level of immunity of InfraRed noise from direct

sunlight, CFL lighting and Flat Panel TV’s (including Plasma, LCD and LED), in rare cases, the

IRLM IR Receiver may have to be moved to a different location if the unit is picking up

unexpected interference. This interference may, in severe cases, prevent the system from

working. You can identify interference when the InfraRed Emitters are lit or blinking, even

when you’re not using a remote control transmitting at the time.

After repositioning, check to see if the ebode IR Link M operates the satellite Receiver or

other components. If the ebode IR Link M still does not work, reposition the IRED Emitter(s).

It may not be located directly over the component’s InfraRed receiving "window".

Consult the owner's manual of the unit or the manufacturer for the exact location of the

InfraRed "window". If the ebode IR Link M does not work at all, please check all the

connections.

Do you still have questions? Please refer to www.ebodeelectronics.eu

9. Technical information

Power Supply: 230V~50Hz, 12VDC 100mA; 2.1mm

IR emitting diode cable: 2 IR LEDs

Cable length: 3 m total, 1 m from HUB to IR LEDs, and/or 3.5 mm mono jack plug

Receiver dimensions: 35x10x10mm

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ebode IR Link M Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info