Bedienungsanleitung Ebode VLHD38 (Seite 12 von 98) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

611741

Zoom out

Zoom in

Vorherige Seite

1/98

Nächste Seite

30-1-2015 12 ebode VLHD38

USB Optional: Connect a compatible USB mouse, keyboard, gamepad to the receiver

through USB interface and make sure they are perfectly connected. HINT: if the USB

device is not working, disconnect the USB device and establish a video connection first.

After the video connection is successful established, re-connect the USB cables.

4.6 Pair devices:

The VLHD38 should automatically connect when:

 Both the VLHD38 Transmitter`s Power Buttons are ON

 The source is connected, powered and playing / showing image

 The TV on both Transmitter and Receiver side are Powered, ON and set to the right

input channel for HDMI (depends on where the VLHD38 is connected)

 All cables are connected properly

 30 seconds have been passed (the VLHD38 needs to boot)

 If USB Power has been used; has enough output power (minimum 1.5A)

If the VLHD38 connection fails:

 Press the PAIR button on the VLHD38 Transmitter

 Press the PAIR button on the VLHD38 Receiver

After pairing, the connection is re-established and the system is ready to transport AV

signal. The Receiver TV will show its status (connecting, searching etc.)

In case you have no signal we suggest you to check chapter 5 (Frequently asked

questions) and to find out what has gone wrong.

5. Frequently Asked Questions

Before following the frequently asked questions below, make sure that your receiver and

attached equipment (HD source and display) are all properly connected, switched on and

not in Standby Mode, please give them a 10 second power off reset before taking the

next steps:

No video

1. Are the VLHD38 Power Buttons on both the Transmitter and

Receiver ON?

2. Ensure there is video on the output device (Source).

3. Check the receiver is correctly connected to display

equipment.

4. Make sure all devices are working on supported distance. Draw

them closer and try it again.

5. Is the VLHD38 USB Power Cables are used, make sure there is

enough output power on the USB Power Port (1.5A Minimum).

Power

LED off

1. Make sure the Power Adaptor or Power USB cable is correctly

connected and the voltage is 5V 1.5A or higher.

2. Make sure the power supply would not be interrupted.

Receiver

video

indicating

LED

abnormal

1. Make sure video and audio signals can be transmitted to receiver

successfully.

2. If there are video and audio signal on output devices, please

check the indicating LED to see if something got wrong with it.

3. Make sure the device is working within the supported distance.

Bad

picture

1. Ensure there is video on output devices.

2. Check if the receiver is correctly connected to display equipment

and there is no damage on joints and wires.

3. Make sure all devices are working on supported distance. Draw

them closer and try it again.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ebode VLHD38 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info