Bedienungsanleitung Eccotemp 20HI (Seite 40 von 56) (Englisch)

782667

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

PLEASE NOTE: 20H IS FOR OUTDOOR PERMANENT INSTALLATIONS ONLY AND 20HI IS FOR INDOOR PERMANENT INSTALLATIONS ONLY. THIS MANUAL

AND ALL ECCOTEMP CONTENT IS SUBJECT TO CHANGE WITHOUT NOTICE. PLEASE VISIT WWW.ECCOTEMP.COM/SUPPORT FOR MORE INFORMATION.

Support: Eccotemp.com/help-desk Shop Online: Eccotemp.com/products Store Locator: Eccotemp.com/locator

Phone: 866-356-1992 | Email: Support@eccotemp.com | Address: 315 - A Industrial RD Summerville, SC 29483

English

Insulation blankets, available to the

general public, for external use on

gas water heaters are not

necessary. The purpose of an

insulation blanket is to reduce the

standby heat loss encountered with

storage tank heaters. This water

heater does not store water making

an insulation blanket unnecessary.

The manufacturer’s warranty does

not cover any damage or defect

caused by installation, attachment

or use of any type of energy saving

or other unapproved devices

(other than those authorized by

the manufacturer) into, onto or in

conjunction with the water heater.

The use of unauthorized energy

saving devices may shorten the

life of the water heater and may

endanger life and property.

The manufacturer disclaims any

responsibility for such loss or injury

resulting from the use of such

unauthorized devices.

WARNING: If

local codes require

external application of

insulation blanket kits

the manufacturer’s

instructions included

with the kit must be

carefully followed.

Insulation Blankets

Hot and Cold Pipe

Insulation Installation

For increased energy eciency,

use pipe insulation. Please install

the insulation, according to the

illustrations above, making sure to

insulate all the way to the top. Do not

cover any drain or pressure valve(s).

Pipe Installation

Inlet Pipe and Outlet Pipe Installation

Use pressure resistant pipe to connect the inlet and outlet

water pipes of the water heater and the local water pipe

(Make sure to place the rubber ring). Before connecting the

inlet water pipe, ush the inside of the pipe. Make sure to

placed the rubber ring before connecting the inlet water pipe.

Flush the inside of the pipe.

NOTICE: The hot and cold pipes

should be insulated to help provide

additional freeze protection.

During Installation of this water heater

Do’s

• DO check inlet gas pressure to ensure that it is within the range specied on the rating plate.

• DO provide adequate air for combustion and ventilation as discussed in the Use & Care Manual and the

National Gas Code (CAN/CGA B 149 in Canada).

• DO maintain proper clearances to combustibles as specied by applicable code.

• DO ensure that the ue terminal location complies with the guidelines found in the Use & Care Manual and

National Fuel Gas Code (CAN/CGA B 149 in Canada).

Dont’s

• DON’T block or restrict Air Intake Opening located on the back side of the water heater.

• DON’T remove the front cover unless absolutely necessary. This should only be done after being examined by a

qualied service technician.

• DON’T install this product where standing water may occur.

20HI Installation

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Eccotemp 20HI Seite 40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info