Bedienungsanleitung Eccotemp 45HI-LP (Seite 28 von 56) (Englisch)

782651

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

PLEASE NOTE: 45H IS FOR OUTDOOR PERMANENT INSTALLATIONS ONLY AND 45HI IS FOR INDOOR PERMANENT INSTALLATIONS ONLY. THIS MANUAL

AND ALL ECCOTEMP CONTECT IS SUBJECT TO CHANGE WITHOUT NOTICE. PLEASE VISIT WWW.ECCOTEMP.COM/SUPPORT FOR MORE INFORMATION.

Support: Eccotemp.com/help-desk Shop Online: Eccotemp.com/products Store Locator: Eccotemp.com/locator

Phone: 866-356-1992 | Email: Support@eccotemp.com | Address: 315 - A Industrial RD Summerville, SC 29483

English

Water Supply Connections....

To conserve energy and to prevent freezing, insulate both cold

and hot water supply lines. DO NOT cover the drain valves.

Install a shuto valve near the inlet of the water heater for service

and draining purposes. Before connecting the water supply pipe to

the water heater, open the shuto valve ·and clean out sand, debris,

air, caulking material, etc. inside the pipe. Connect to the water

inlet, then check water ow. Close the shuto valve and clean the

water lter.

If a water heater is installed in a closed water supply system, such

as one having a backow preventer in the cold water supply line,

means shall be provided to control thermal expansion. Contact

the water supplier or local plumbing inspector on how to control

this situation.

CAUTION: This water heater must only be used with the following water supply system conditions:

• With clean, potable water free of corrosive chemicals, sand, dirt, or other contaminates.

• With inlet water temperatures above 32°F, but not to exceed 90°F.

• Free of lime and scale deposits.

• DO NOT reverse the hot and cold water connections. The water heater will not operate.

To ensure proper operation of the water heater, the following water pressure guidelines should

be followed:

• Operation of the water heater requires the minimum water pressure of 14 psi and a minimum

water ow rate of 0.75 gpm.

• Additional water pressure is required for long pipe runs and outlet tting(s) water pressure

drops.

• To maintain proper performance, ensure sucient water supply pressure. The Required

Water Pressure = Min. Operating Water Pressure (14 psi) + Pipe Pressure Loss + Faucet and

Shower Pressure Loss + Safety Margin (more than 5 psi).

• To supply hot water to upper oors, additional water pressure (0.44 psi/ft) must be ensured.

The measurement should be calculated by the distance between the water inlet of the water

heater (ground level) to the hot water faucet (upper oor level).

• Well water systems should be set at a range of 50-60 psi.

• When the water is supplied from a water supply tank, the height of the tank and the diameter

of the pipes and their relation to water pressure, should be taken into consideration. Gravity

water pressure is not recommended.

IMPORTANT: Do not apply heat to the HOT or COLD water connections. Any heat applied to the

water supply ttings will permanently damage the internal components of the water heater.

NOTICE: If the water ow resistance of a shower head is too high, the burner in the water heater will

fail to ignite. Keep the shower head clean from debris that could cause additional pressure drop.

Notice: If using mixing valves on the outlet, choose one which prevents cold water pressure from

overcoming hot water line pressure.

DO NOT use pipes with smaller diameters than the water supply connection of the water heater.

Be sure to connect the water inlet and the hot water outlet as shown on the water heater. If reversed,

the water heater will not function.

Installation of unions or exible copper connections are recommended on the HOT and COLD water

lines, so that the water heater may disconnect easily for servicing if necessary.

Plumbing should be carried out by a qualied plumber in accordance with local codes. Use approved

plumbing materials and tools only.

Install a Check Valve between the water heater and the water shuto valve. (See illustration below).

45-HI

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Eccotemp 45HI-LP Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info