Bedienungsanleitung Eccotemp EccoFlo (Seite 4 von 10) (Englisch)

782670

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

Phone: 866-356-1992 | Email: Support@eccotemp.com | Address: 315 - A Industrial RD Summerville, SC 29483

English

Support: Eccotemp.com/help-desk Shop Online: Eccotemp.com/products Store Locator: Eccotemp.com/locator

INSTALLATION

STEP 1. Remove shipping plugs from pump ports. Some water from factory testing may spill out.

STEP 2. Connect ttings supplied with the pump to your hoses. If using the slip-on barb

connections use hose clamps.

STEP 3. Mount pump horizontally or vertically. Read mounting instructions below.

STEP 4. Install inlet and outlet port connectors. Do not overtighten.

STEP 5. Install the strainer in an accessible location between the tank and pump inlet. This

strainer or equivalent is recommended.

MOUTING

(Please read before completing steps)

• The pump can be at the same level or below the water tank. It may be positioned above the

water tank if needed, as it is capable of a 6ft. (1.8m) vertical prime. Horizontal inlet tubing will

allow priming to 30ft (9m)

• Consider a dry location that allows easy access if maintenance is required. The pump should

not be located in an area of less than one cubic foot unless adequate ventilation is provided.

Excessive heat may trigger the integral thermal breaker and interrupt operation. When the

temperature drops the breaker will automatically reset and start proration.

• The pump can be mounted horizontally or vertically. If mounting of the pump vertically, the

pump head should be in the down position.

• The mounting feet are intended to isolate the pump from the mounting surface; over-

tightening, attening, or use of oversized screws will reduce the ability to isolate vibration

and noise through the lines.

INSTALLATION INSTRUCTIONS

• Solid surface

• Accessible location away from living quarters

• Properly sized wiring

• Proper electrical protection

• Strainer on plumbing elbows and valves near the pump

• Minimize ow restrictions in the system

WIRING

STEP 1. Use 14 gauge stranded wire to 20’, 12 gauge to 50’ from power source.

STEP 2. Use a 10-15 amp rated on-o switch on the (+) (red) motor lead

STEP 3. Install a 10 amp fuse protection on the positive lead.

ELECTRICAL

(Please read before completing steps)

• The pump should be on a dedicated (individual) circuit protected by the specied fuse

indicated on the motor label.

• A U/L, CE etc. approved marine duty (ignition protected) switch rated at above 15 amps is

recommended and must interrupt current ow on the positive (+ red) lead.

• The pump must be grounded to a known ground (battery). The ground wire must be the

same size (gauge/Mm2) as the positive wire.

• Wire sizing: Proper wire sizing is required for good pump operation. If the wire is too small,

low voltage will aect the pump performance and can create re hazard.

• The total current draw on the circuit must not exceed 15 amps. If the pump is used in

conjunction with other components, overload current protection (fuse or circuit breaker) and

wire size must be for the total amp requirements of all devices on the circuit.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Eccotemp EccoFlo Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Eccotemp EccoFlo

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info