Bedienungsanleitung Eccotemp EL22 seriesEL (Seite 51 von 56) (Englisch)

782659

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

PLEASE NOTE: EL22 IS FOR OUTDOOR PERMANENT INSTALLATIONS ONLY AND EL22-I IS FOR INDOOR PERMANENT INSTALLATIONS ONLY. THIS MANUAL

AND ALL ECCOTEMP CONTENT IS SUBJECT TO CHANGE WITHOUT NOTICE. PLEASE VISIT WWW.ECCOTEMP.COM/SUPPORT FOR MORE INFORMATION.

Phone: 866-356-1992 | Email: Support@eccotemp.com | Address: 315 - A Industrial RD Summerville, SC 29483

English

Support: Eccotemp.com/help-desk Shop Online: Eccotemp.com/products Store Locator: Eccotemp.com/locator

Error

Code Error Description Possible Cause What To Do

E0 Hot water sensor failure Junction port loose,

Short circuit Call for Service

E1 Ignition systeme failure

The gas valve is not opened

or fully opened, Water shut-

o valve is not open, Junction

port loose

Check and open gas fully,

Check and open water valve,

Call for Service

E2 There is ame when no

water coming in Electric circuit problem Call for Service

E3 Over-heating protection Dry Combustion, Problem of

over heating controller Call for Service

E4 Cold water temperature

sensor

problem with sensor, problem

with sensor’s plug or socket,

none of the above

replace the sensor, x it,

replace the computer board

E5 Pressure Switch Motor problem, Voltage of

power supply is too low Call for Service

E6 Over-heating

Gas pressure is too high,

Water shuto valve is not

fully opened, The temperature

is set too low

Check shut-o valve and

open fully, Increase

temperature setting

E7 solenoid valve

open circuit of the valve, short

circuit of the valve, none of

the above

connect the valve, replace the

valve, replace the computer

board

E8 vent pipe block vent pipe is blocked clean the pipe

If the error code remains shown:

• Close the hot water faucet and turn o the\

switch on the remote control.

• Take the proper action shown below and

attempt operation of the water heater again.

• If the error code is still shown:

• Turn o the hot water faucet and turn o

the switch on the remote control.

• Take note of the error code displayed and

call the customer service assistance

number in the “If You Need Service”

When an error code is displayed:

• Close the hot water faucet, turn o the

switch on the remote control.

• Wait for about 5 minutes before turning the

switch on again.

• Open the hot water faucet.

NOTICE: If an error code other than those listed

below is displayed, immediately turn o the hot

water faucet, take note of the error code, turn

o the switch on the remote control and call the

customer assistance number.

Error Code Guide

CAUTION: For your safety DO NOT attempt repair of gas piping, remote control,

burners , vent connectors or other safety devices. Refer repairs to qualied service

personnel.

CAUTION: Make certain power to water heater is “OFF” before removing protective

cover FOR ANY REASON.

CAUTION: Label all wires prior to disconnection when servicing controls. Wiring

errors can cause improper and dangerous operation. VERIFY PROPER OPERATION

AFTER SERVICING.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Eccotemp EL22 seriesEL Seite 51

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info