Bedienungsanleitung Eclipse CD5425E (Seite 46 von 62) (Englisch)

654694

Zoom out

Zoom in

Vorherige Seite

1/62

Nächste Seite

 110 

Various Settings

How to operate the Sound Adjustment Mode

This unit is equipped with various functions to compensate the acoustic characteristics inside the

vehicle.

The following adjustments can be made in the sound adjustment mode.

• Crossover (FRONT/REAR/NON-FADER)

• Switching the non fader phase.

Crossover

The frequency band that is stored by audio media such as CDs is a fairly wide range from 20 Hz to 20

kHz, and it is difficult for a single speaker to be able to play back all frequencies in such a wide range.

Because of this, several speakers can be used, with different frequency bands (such as treble,

medium and bass) allotted to each speaker so that wide frequency ranges can be played back.

The "Crossover" function is used to allot the frequency ranges that are to be played back by each

speaker in accordance with the installed speaker units and the layout of the speakers, in order to

obtain the maximum level of performance from the speakers and to provide the most stable

frequency characteristics.

The crossover function includes a high-pass filter (HPF) for playing back treble sounds, and a low-

pass filter (LPF) for playing back bass sounds. In addition, the HPF and LPF are used in

combination in order to play back sounds in the medium range.

For example, when adjusting the HPF, frequencies that are lower than the specified frequency are

progressively dampened, rather than simply not being played back at all. The "slope" adjustment

function is the function that is used to adjust these dampening characteristics.

The slope characteristics of a filter are such that with larger slope values (for example 12 dB/oct),

the slope becomes steeper, and so the amount of sound mixing in with neighboring bands becomes

less so that only the target band is played back. However, it also causes the merging of sound

between speakers to become poorer and can result in greater distortion.

• The crossover function is a filter that allocates specified frequency bands.

• A high-pass filter (HPF) is a filter that cuts out frequencies that are lower than the specified

frequency (bass range) and allows higher frequencies (treble range) to pass through.

• A low-pass filter (LPF) is a filter that cuts out frequencies that are higher than the specified

frequency (treble range) and allows lower frequencies (bass range) to pass through.

• The slope is the signal level at which frequencies that are one octave higher or one octave lower

are dampened.

The larger the slope value, the greater the slope. In addition, when "PASS" is selected, the slope

is eliminated (sound does not pass through the filters), so that the crossover function has no

effect.

About Sound Adjustment Mode

fc1(LPF) fc2(HPF) fc3(LPF) fc4(HPF)

20kHz

-3dB

Bass range Mid range Treble range

20Hz

fc*: Cutoff frequency

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Eclipse CD5425E Seite 46

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Eclipse CD5425E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info