Bedienungsanleitung Ecm Classica II (Seite 19 von 53) (Deutsch, Englisch, Holländisch)

647412

Zoom out

Zoom in

Vorherige Seite

1/53

Nächste Seite

ENGLISH

Instruction manual CLASSIKA

4 MACHINE INSTALLATION

4.1 Preparation for the installation

• Place the machine on an even and stable surface. You can regulate the height of the machine by

adjusting the feet of the machine.

• Never place the machine on hot surfaces.

4.2 Electrical connection

• Make sure that the local main supply voltage corresponds to the information given on the type plate

on the front panel of the espresso machine.

• Plug the machine only into an earthed socket and do not leave it unattended.

• Do not roll or bend the power cord.

• Do not use an extension cord/ do not use a multiple socket.

5 FIRST USE

5.1 First use

Read the instruction manual carefully before operating the machine.

Before starting the machine, check if:

• the steam/ hot water valve is closed.

• the machine is switched off. (Power switch in lower position.)

• the power cord is disconnected.

• the drip tray is inserted accurately.

Now you can begin to operate your machine:

1 Remove the cup heater tray.

2 Fill the water tank with fresh water, deficient in lime. Replace the cup heater tray.

3 Insert the plug in the wall socket. Turn the power switch in upper position. The machine is now on.

Important!

Also for the first use, the boiler has to be filled.

4 Place a small container (e. g. a milk jug) under the steam/ hot water valve. Open the steam valve by turning it

anticlockwise and move the pump/ hot water switch into the upper position. A pump sound should be audible.

Now the boiler fills with water. At first use, it can take a few seconds before the water comes out of the steam

valve. Please allow that approx. 600 ml of water come out of the valve. In this way, the boiler is flushed and

filled with fresh water. This allows you to constantly renew the boiler water in daily use. Switch off the pump/

hot water switch by moving it into the lower position and close the steam/ hot water valve.

5 Dispense water by moving the group lever into the upper position. Then put back in lower position.

6 The machine heats up and the orange control lamp for heating control lights up.

7 As soon as the optimum temperature (approx. 110-120 °C) is reached, the heating shuts off automatically and the

control lamp for heating control goes out. The indicator of the pump pressure gauge may move slightly during the

heat-up phase.

8 Clamp the empty filter holder to the brewing group to preheat filter and filter holder. You can accelerate this

process by dispensing water from the brewing group.

9 For the first filling-up of the boiler, a large amount of water is required. Therefore, refill the water tank with water

after the first use.

10 The machine is now ready for use. Put the cups on the cup heater tray in order to preheat them. Then enjoy your

coffee!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ecm Classica II Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info