Bedienungsanleitung Ecm mechanika profi (Seite 23 von 58) (Deutsch, Englisch, Holländisch)

362350

Zoom out

Zoom in

Vorherige Seite

1/58

Nächste Seite

ENGLISH

Instruction manual MECHANIKA · MECHANIKA PROFI

2 Turn the machine on (power switch in position “1”).

3 Wait until the pressure gauge indicates approx. 1.0-1.25 bar.

4 Depending on the ambient temperature, the heat-up phase is approx. 15 minutes.

5 The machine is now ready for use.

6 Move the group lever with the inserted filter holder into the upper position and release some hot water. Thus,

the filter holder will be completely heated.

It is recommended to leave the filter holder in the brewing group to keep it warm for optimum

temperature for coffee dispension.

6.2 Manual adjustment of the brewing pressure

You can adjust and change the brewing pressure at will by turning the adjusting screw choosing a value between

approx. 8.5 and 12 bar.

To adjust the brewing pressure, proceed as follows:

1 Open the cup warmer tray.

2 Place the filter holder with the blind filter into the brewing group

3 Operate the group lever and read the pump pressure gauge.

4 Choose the desired brewing pressure by turning the adjusting screw. Use a coin or a flat screwdriver for turning.

You can reduce the brewing pressure by turning the screw anti-clockwise and increase it by turning it clockwise.

5 Read the pump pressure group to see the adjusted brewing pressure.

6 Now the machine is ready for use again.

6.3 Preparing coffee

Use the filter holder with 1 spout and the correspondent filter (1 cup) for the preparation

of 1 cup. Use the filter holder with 2 spouts and the big filter (2 cups) for the

preparation of 2 cups. Make sure that the filter is firmly locked in the filter holder.

Put the ground coffee (with the respective grinding degree for espresso or

Café Crème) into the filter.

Use 1 level measuring-spoon of coffee for each cup (approx. 7 g).

Do not overfill the measuring-spoon, like shown in the figure aside!

Slightly compress the ground coffee with the tamper. Clamp the filter holder firmly

to the group.

Put the cup under the spout of the filter holder (for the preparation of 2 cups, put 1 cup under each spout).

Move the group lever into the upper position. During coffee preparation, the overpressure is conducted back over the

water tank adapter. When the cup is filled, move the group lever into the lower position.

The remaining pressure/water will be discharged into the drip tray by the lower part of the infusion cylinder.

The pump pressure can be read off the pump pressure gauge. If the coffee powder is too rough, a brewing pressure

over 9 bar is not possible.

Advice: After the brewing process, the gauge still indicates a certain pressure. Only when preparing another cup of

coffee the buildup of pressure is visible again.

If the group lever is not moved into the lower position properly, hot water and grounds disposal can squirt out of the

group while taking out the filter holder. This can cause injuries.

 Only freshly ground coffee allows an optimal coffee result. Therefore, use a professional coffee

grinder. In our assortment you will find several professional and compact coffee grinders.

 We recommend to use a stainless steel tamper with a diameter of 58 mm for optimum tamping.

6.4 Dispensing hot water

1 Place an adequate water container (with a heat-insulating handle) under the hot water dispenser. After having

moved the power switch in lower position, you can dispense water (e. g. for tea) by opening the hot water lever.

2 After dispensing water, switch the machine on again. The boiler will be filled with fresh water automatically.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ecm mechanika profi Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info