Bedienungsanleitung Ecoforest Cordoba (Seite 66 von 228) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

742218

Zoom out

Zoom in

Vorherige Seite

1/228

Nächste Seite

A039

Burning pot cleaning failure.

Sensors do not detect opening and closing of the

burning pot’s lid after 3 cleaning attempts.

• Doors or ash drawer cover badly closed.

• Burn pot base open or not properly closed.

• Sensor damaged.

• Wiring or connector disconnected or loose.

• Periphery damaged.

• Engine damaged.

A040

A045

MODBUS RS485 communication error between

the CPU and its environment.

• Disconnected cable.

• Broken cable, replace with a new one.

A041

Zoning Periphery 2

• Zoning Failure 2.

• MODBUS cable failure

A042

Zoning periphery 3

• Zoning fault 3.

• MODBUS cable failure

A051

Pneumatic silo control without pellets.

• External silo has no pellets.

• Pipeline.

• Open pneumatic silo lid.

A052

A053

Hopper silo 1 sensor without pellet.

• Sensor defective or badly calibrated.

• Without pellet.

• Conveyor screw of external silo stuck.

A054

Silo control 3 sensors.

• One of the sensors damaged.

• Without pellet.

A055

Burning pot cleaning.

• Burning pot performing configured cleaning.

• Burning pot cleaning carried out and awaiting

demand.

A099

Lack of pellets, impossible to reach the minimum

temperature for gas exhaustion (80 °C).

• Filling the hopper.

• Stopped gear motor.

• The safety thermostat has tripped.

A101

Maximun flow temperature in zone 1.

• Air in the circuit.

• Little dissipation of the energy generated.

• Too heavily used.

• Shortcut in NTC.

A102

Maximun flow temperature in zone 2.

A103

Maximun flow temperature in zone 3.

A104

Minimum flow temperature in zone 1.

• Installation of boiler badly measured.

• Boiler working to low levels of power.

• Disconnected NTC.

• NTC badly placed.

A105

Minimum flow temperature in zone 2.

A106

Minimum flow temperature in zone 3.

A107

Maximun room temperature in zone 1.

• Too much temperature in the room.

• Disabling the room sensor.

• Increasing operating temperature.

A108

Maximun room temperature in zone 2.

A109

Maximun room temperature in zone 3.

A110

Minimum room temperature in zone 1.

• Low temperature in the room.

• Disabling the room sensor.

• Lowering operating temperature.

A111

Minimum room temperature in zone 2.

A112

Minimum room temperature in zone 3.

A120

MODBUS RS485 communication error between

the CPU and its environment. Zone 1

• Disconnected cable.

• Broken cable, replace with a new one.

A121

THT1 does not communicate.

• Review configuration.

• Check zone THT connections.

A122

THT2 does not communicate.

A123

THT3 does not communicate.

6.1. RESET ALARM.

The switching off process triggered by an alarm depends on the machine’s previous state, its configuration and

on a series of external factors. Once the alarm process has ended, the unit can be rebooted after having revised the

alarm table and taken the necessary measures.

Drawing 59

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ecoforest Cordoba Seite 66

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ecoforest Cordoba

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info