Bedienungsanleitung Economy by Ferm HDM1024 - EBH-850KN (Seite 5 von 12) (Englisch)

763890

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

each machine function is given in the diagram

(Fig.C) on page 2.

1 = Demolition hammer/chisel

2 = Rotary hammer drill

3 = Drilling

Switching On/Off

To start the drill, squeeze the trigger.•

To stop the drill, release the trigger.•

Installing dust catcher

Fig. C

The dust catcher prevents large amounts of

drilling dust entering the machine when drilling

into ceilings:

Remove the drill bit.•

Slide the dust catcher over the shaft of the drill •

bit.

Place the drill bit with catcher in the drill •

chuck.

Always replace a damaged dust catcher •

immediately.

4. Maintenance

Take care that the machine is not

connected to power whenever

maintenance work on the mechanical

parts is taking place.

The machines are designed to function

problem-free for a long period with a minimum

of maintenance. Through regular cleaning and

correct treatment, you help assure a long working

life for your machine.

Defects

The machine should be regularly inspected for

the following possible defects, and repaired if

necessary.

Damage to power cord•

Broken on/off trigger assembly.•

Short circuiting.•

Damaged moving parts.•

Trouble shooting

1. When switched on, the motor does not

turn.

Failure in power supply.•

Check the power supply.•

Poor contact in the on/off trigger.•

Repair or replace the trigger assembly.•

Mains voltage too low.•

Extension lead too long, or too light.•

Damaged motor.•

Have your machine repaired by an expert.•

Carbon brushes worn.•

Replace the carbon brushes•

2. Motor generates excessive noise, and

runs too slowly or not at all.

Motor is overloaded due to excessive •

pressure or drilling depth.

Reduce the pressure or drilling depth, •

reduce power.

Damaged motor.•

Have your machine repaired by an expert.•

Supply voltage too low.•

Adjust the supply voltage.•

Carbon brushes worn.•

Replace the carbon brushes•

3. Overheating in the transmission case.

Overloading of machine, or blunt drill bit•

Reduce the loading, or hone the drill bit.•

Reduced voltage.•

Adjust the supply voltage.•

4. Heavy sparking from the motor.

Inspect the carbon brushes for wear.•

Replacing carbon brushes

Replace both carbon brushes at the same •

time.

Regularly check the carbon brushes for wear •

and defects.

Always replace worn-out carbon brushes.•

Always keep the carbon brushes clean, and •

make sure that neither brush is obstructed.

Open the machine to inspect/replace the •

carbon brushes.

Remove and replace the carbon brushes if •

necessary.

Reassemble the rear handgrip.•

Cleaning

Clean the machine casings regularly with a soft

cloth, preferably after each use. Make sure that

the ventilation openings are free of dust and

dirt. Remove very persistent dirt using a soft

cloth moistened with soapsuds. Do not use any

solvents such as gasoline, alcohol, ammonia,

etc. Chemicals such as these will damage the

synthetic components.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Economy by Ferm HDM1024 - EBH-850KN Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info