Bedienungsanleitung Economy hdm 1015 ebf 850k (Seite 5 von 22) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Norwegisch)

388952

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

Ferm 05

40 Ferm

• Whenever any of the problems mentioned

above appear, immediately cease using the

machine and have it repaired by an expert.

Electrical safety

Always check that the mains voltage is

the same as on the type plate of the

machine.

The machine is double insulated; there-

fore, no earth connection is required.

Replacement of power cords or plugs

Immediately dispose of old cords and plugs once

they have been replaced. It is dangerous to plug

a loose power cord into a mains power socket.

Use of extension leads

Only ever use approved extension leads that are

suitable for the power rating of the machine.

The

minimum core thickness is 1.5 mm

. Whenever

using a reel extension lead, always fully unroll

the lead.

3. OPERATING

Hammer drills require very little operator

pressure. Excessive pressure on the tool

can lead to unnecessary overheating of

the motor, and burning of the driven tool.

Auxiliary handgrip

The auxiliary handgrip can be rotated 360º

around the drill head, enabling safe and comforta-

ble operation, for both left and right-handed users.

• Loosen the handgrip by turning it anticlockwise.

• Rotate the handgrip to the desire position.

• Retighten the handgrip in the new position.

Exchanging and removing drill bits

Fig. A + B

Before exchanging bits, first remove the

power plug from the wall socket.

Inspect bits regularly during use. Blunt

bits should be re-sharpened or repla-

ced.

• Lightly lubricate the shaft of the drill bit before

inserting into the machine.

•

Place the shaft of the drill bit into the opening of

the drill chuck and twist until latched.

• To release and remove the drill bit pull back the

collar of drill chuck .

Setting depth gauge

• Loosen the handgrip by turning it anticlockwise.

•

Insert the depth gauge ruler through the hole in

the auxiliary handgrip.

• Slide the ruler to the desired depth.

• Retighten the screw firmly.

Function selection switch

Fig. D

The correct position of the selection switch for

each machine function is given in the diagram on

page 3.

1 = Demolition hammer/chisel

2 = Rotary hammer drill

3 = Drilling

Switching On/Off

• To start the drill, squeeze the trigger.

• To stop the drill, release the trigger

Installing dust catcher

Fig.C

The dust catcher prevents large amounts of dril-

ling dust entering the machine when drilling into

ceilings.

• Remove the drill bit.

•

Slide the dust catcher over the shaft of the drill

bit.

• Place the drill bit with catcher in the drill chuck.

• Always replace a damaged dust catcher imme-

diately.

4. MAINTENANCE

Take care that the machine is not con-

nected to power whenever maintenance

work on the mechanical parts is taking

place.

The machines are designed to function problem-

free for a long period with a minimum of mainte-

nance.

Through regular cleaning and correct tre-

atment, you help assure a long working life for

your machine.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Economy hdm 1015 ebf 850k Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info