Bedienungsanleitung Eden HA700 (Seite 5 von 23) (Englisch)

547014

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

CONTROL PANEL

CHOOSING THE DETECTOR TYPE

Zone 1 provides standard intruder monitoring with

normal ARM and PART-ARM function.

Zone 2 provides ARM function.

Panic zone is used to provide 24 hour monitoring of

areas requiring continuous security protection even

while the system is disarmed. Activation of any

detector will immediately initiate a full alarm condition.

Note: Up to 10 different ID code of detectors can be

learned in Zone 1, Zone 2 and panic zone respectively.

Note: Up to 4 pcs of remote controller, 1 pc of wireless

keypad (SA401) and 1 pc each of outdoor and indoor

siren can be learned by Control Panel.

LEARNING ID CODE OF DETECTORS

Upon completion of selecting type of detector as

mentioned above, proceed with the following steps:

Press

User access code

The Control Panel will enter learning mode of which UI

indication refers to “UI_Wait”. The Control Panel has

a 30-second to learn one ID code from the

detector/remote controller/wireless keypad.

For detector, press the tamper switch on the detector

so as to emit ID code to the Control Panel.

Three LED will flash in sequence on the Control Panel,

it helps you to determine which zone the detector

should be assigned. Users have a 6-second to input

zone number. If the detector is to be assigned in Zone 1,

press keypad ; Zone 2, press keypad

;

whereas Panic zone, press keypad on the

Control Panel.

Note: It is recommended that the smoke detector and

flood detector are assigned to panic zone.

For wireless keypad, press the tamper switch on the

device so as to emit ID code to the Control Panel

automatically.

For remote controller, press any key on it so as to emit

ID code to the Control Panel automatically.

If failed refers to UI_Error indication for confirmation.

CLEARING ID CODE OF DETECTORS

Press

User access code

The Control Panel will enter clearing mode of which UI

indication refers to “UI_Wait”. Users have 15-second

to clear ID code.

Following is the instruction to clear ID code stored in

each zone.

Press for zone 1

User access code

Press for zone 2

User access code

Press for panic

User access code

Press for remote

User access code

Press for keypad

User access code

Press for all ID

User access code

LOCATING THE CONTROL PANEL

When choosing a suitable location for the Control Panel,

the following points should be considered.

1. The Control Panel should be located in a position

out of sight of potential intruders and in a safe

location, but easily accessible for system operation.

2. The Control Panel should be mounted on a sound

flat surface to ensure that the rear tamper switch on

the Control Panel is closed when the Panel is

mounted. The Control Panel should be mounted

at a convenient height of between 1.5 and 2m and

in a position where it will be seen each day.

Note: If small children are in the household, a

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Eden HA700 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Eden HA700

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info