Bedienungsanleitung Edilkamin ANIA (Seite 31 von 192) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

672465

Zoom out

Zoom in

Vorherige Seite

1/192

Nächste Seite

- 33 -

ENGLISH

A: À ue in insulated steel compliant with EN 1856

B: minimum height of 1.5 m and in any case above the height of the

roof gutter

C-E: air intake from inside room (minimum internal section: 80 cm²)

D: steel À ue, inside existing brick-built chimney.

SMOKE OUTLET

The stove must have its own smoke outlet (the smoke can-

not be discharged into a smoke À ue used by other devices).

The smoke is discharged through the 8 cm diameter outlet at

the back

of the stove

The smoke outlet must be connected to outside by means of

suitable steel pipes EN 1856 certi¿ ed.

The pipe must be hermetically sealed.

An example of a suitable pipe bears the following

information:T600 N1 D V2 L50050 G70 (not suitable with T <

200; 0 indicating no resistance to the À ow of soot).

The material used to seal and if necessary insulate the pipes,

must be resistant to high temperatures (high temperature silico-

ne or mastic).

The only horizontal section allowed may be up to 2 m long up

to three 90° bends (in relation to the vertical).

A vertical section of at least 1.5m and an anti-wind terminal

is necessary (if the discharge outlet is not in a chimney À ue -

reference UNI 10683).

The vertical duct can be internal or external.

If the smoke channel is outside, it must be appropriately insu-

lated. If the smoke channel is ¿ tted inside a chimney À ue, the

latter must be suitable for solid fuel.

If it is wider than 150 mm in diameter it must be improved by

entering a pipe that has a suitable cross-section and is made of

suitable material (e.g. 80 mm diameter steel).

All sections of the smoke duct must be accessible for inspec-

tion.

The chimney pots and smoke ducts connected to the solid fuel

appliances must be cleaned once a year (verify whether a speci-

¿ c legislation exists in your country).

Failure to regularly inspect and clean the stove increases the

probability of a ¿ re occurring in the chimney pot. In that case,

proceed as follows: Do not use water to extinguish the ¿ re;

Empty the pellet hopper; Contact specialist personnel before

reigniting the stove.

The stove is designed to work under any weather conditions.

In case of particular conditions, such as strong wind, the safety

system may be activated, which results in the stove being extin-

guished.

If this happens, do not operate the stove with the safety devices

disabled. If the problem persists, contact our Technical Service

Department.

INSTALLATION

CHIMNEY POT

The main characteristics are:

- an internal cross-section at the base, which is the same as that

of the chimney À ue

- an outlet cross-section which is no smaller than twice that of

the chimney À ue

- its position must be high enough to catch the wind and avoid

downdraft areas in turbulent wind, it must be high enough to

catch the wind and avoid downdraft areas in turbulent wind.

TYPICAL EXAMPLES

Fig. 1 Fig. 2

111

inspection

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Edilkamin ANIA Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info