Bedienungsanleitung Edilkamin AQUAMAXI 28 (Seite 31 von 182) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

810928

Zoom out

Zoom in

Vorherige Seite

1/182

Nächste Seite

- 31 -

ENGLISH

Fig. 1/a

The fundamental characteristics of the chimneypot are:

- an internal cross-section at the base, which is the same as that

of the chimney À ue.

- an outlet cross-section which is no smaller than twice that of

the chimney À ue.

- its position must be high enough to catch the wind and avoid

downdraft areas in turbulent wind.

In addition to that mentioned above, please consider the

indications stipulated in UNI 10683/2005 standard, para-

graph 4.2: “connection to the smoke outlet system” and its

subsections.

- Use a stainless steel À ue to connect the thermo ¿ replace to the

chimney À ue, adhering with the diameters indicated in the spe-

ci¿ cations table and the guidelines given in the chapter called

“chimney À ues”.

- Verify that all moving parts function properly before setting

the thermo ¿ replace covering in place.

- This system must be tested and ignited for the ¿ rst time

before the covering is set in place.

The base of the thermo ¿ replace covering must allow the

internal air to be recycled. Therefore, suitable slots or apertures

must be made for the air to pass through. Parts of the thermo

¿ replace covering that are made of marble, stone and bricks

must be mounted with a small gap between them and the ¿ re-

place so as to prevent possible breakage due to expansion and

excessive overheating.

Protect wooden parts with ¿ reproof materials.

Fireproof parts of the covering (beams or frames) must not be

in contact with the ¿ replace unit but must be at least 1-2 cm

away to allow a À ow of air that prevents heat accumulation (see

Fig. 1/a).

The housing compartment must be made of masonry or ¿ repro-

of materials and must not have combustible elements inside.

The ¿ replace mantel can be made of ¿ reproof plasterboard

panels or gypsum board and, however, of completely ¿ reproof

material. Air should be allowed to À ow inside the ¿ replace

mantel (through the gap between the door and the beam).

Through convective motion, the air will À ow out from the grille

installed at the top, resulting in heat recovery and preventing

excessive overheating (See Fig. 1/a).

The ¿ replace mantel must have appropriate openings to carry

out maintenance on the ¿ ttings.

In addition to that mentioned above, please consider the in-

dications stipulated in the UNI 10683 standard, paragraphs

4.4 and 4.7: “insulation, ¿ nishing, ¿ replace covering and

safety recommendations”.

Insulating mats must be applied when using an installation

KIT so as to protect it from the heat radiation emitted by

the thermo ¿ replace.

45°

max.45°

inspection

CHIMNEY FLUES AND CHIMNEYPOT

The thermo ¿ replace smoke outlet has a circular crosssection

so that stainless steel pipes can be used. If the chimney À ue

inlet is not vertically above the thermo ¿ replace, the connection

from the ¿ replace to the À ue must not have a narrowing

section or inclinations greater than 45° (¿ g. 1-2-3-4).

The ¿ replace unit must not be connected to a shared À ue.

The fume section must be inspectable and installed in such a

way that it can be cleaned (use inspectable TEEs).

If the chimney À ue is not brand new or too big, it is recommen-

ded to ¿ t in stainless tubes of an appropriate diameter and with

suitable insulation.

If the chimney À ue is installed outside, it is recommended to

use an insulated, double walled, stainless steel À ue.

The characteristics of the construction must be suitable to

withstand a smoke temperature of at least 450° C, with parti-

cular reference to the mechanical resistance, insulation and the

gas tight sealing.

The À ue must be certi¿ ed under EN 1856.

The junction of the steel À ue inlet and the smoke outlet of the

¿ replace must be sealed with high temperature mastic.

Have quali¿ ed personnel clean the À ue once a year.

INSTALLATION

INSTALLATION COVERING, FIREPLACE

MANTEL

If combining with a pre-fabricated Edilkamin covering, to de¿ -

ne the exact positioning of the thermo ¿ replace, it is important

to take the chosen covering model into consideration.

The positioning is implemented according to the model chosen

(refer to the installation instructions found inside the packaging

of each thermo ¿ replace covering).

Always ensure the thermo ¿ replace is level during the installa-

tion process.

- Drill a hole into the wall or the À ooring for the external air

intake and connect the air adjustment mechanism to the hole as

described in the chapter called “external air inlet”.

Hot air ŏ ow

grille

Mantel

Door slider

guide

Metal mantel

Hood

Wooden

beam

Front part

Air inlet in the

mantel

sliding door

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Edilkamin AQUAMAXI 28 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info