Bedienungsanleitung Edilkamin Big (Seite 13 von 62) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

810741

Zoom out

Zoom in

Vorherige Seite

1/62

Nächste Seite

- 13 -

ENGLISH

For only one

adjacent room

1 KIT 8

For two adjacent

rooms use

2 KIT 8

For one adjacent

room use

1 KIT 9

Fig. A Fig. B Fig. C

PRINCIPLE OF OPERATION

Range of wood burning stoves with hot air production.

The stoves are built with a cast iron front, whilst the structure of

the ﬁ rebox is made of extra-thick steel.

The entire ﬁ rebox is covered in ECOKERAM®, a special refrac-

tory material obtained from casting.

All models are equipped with secondary and tertiary air injec-

tion, the latter is used for cleaning the glass.

The ﬂ ue pipe can be connected at the top or rear of the stove to

facilitate installation.

Two different operating modes are used to control combustion air:

- AUTOMATIC

- MANUAL

There are two controls located on the lower grate of the stoves:

- “automatic” mode selector switch (S).

- lever for adjustment in “manual” mode (L).

Manual mode:

Position the switch “S” to MANUAL, fully inserted in the cast

iron grate; the control lever “L” controls the amount of air and

therefore the strength of the ﬂ ame from minimum (lever posi-

tioned on the left) to maximum (lever positioned on the right).

Automatic mode:

Position the switch “S” to AUTOMATIC, fully withdrawn

from the grate; the lever “L” must be moved fully left.

In this way, thanks to a thermostatic valve, the stove will auto-

matically adjust the strength of the ﬂ ame according to the tem-

perature of the ﬁ rebox: when the ﬁ rebox is cold, for example on

ignition, the valve will allow the maximum amount of air in to

facilitate this stage; as the temperature in the ﬁ rebox increases,

the valve will slowly decrease the amount of air allowed in,

preventing overheating in the room where the stove is installed

and excessive and unnecessary consumption of wood.””

The stoves are equipped with an 800 m³/h fan that can be adju-

sted from the mimic panel. This makes it possible to channel hot

air so that it can be conveyed to heat rooms adjacent to the place

of installation.

Two Ø10 cm male pipe unions are located on the back of the

stove for connection of the hot air ducting.

KIT 8 or KIT 9 can be used to heat one adjacent room.

• Kit 8 can be used to convey some of the hot air to an adjacent

room and some to the place of installation (Illustr. A).

• Kit 9 can be used to convey all of the hot air produced to an

adjacent room (Illustr. B).

Two Kit 8s must be used to heat two adjacent rooms

(Illustr.C)

HOT AIR CIRCULATION

1) air inlet

2) outlet for hot air conveyable to adjacent rooms

3) outlet for hot air in the room

4) upper smoke outlet

5) rear smoke outlet

6) hot air fan

Auto/man.

selector switch Manual adjustment lever

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Edilkamin Big Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info