Bedienungsanleitung Edilkamin Cherie 11 Evo ATC (Seite 29 von 84) (Englisch)

810753

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

ENGLISH

INSTALLATION

INSTALLER

FLUE SYSTEM

(

Fumes duct, flue and chimney pot

)

This chapter has been drawn up pursuant to European

regulations EN 13384, EN 1443, EN 1856 and EN

1457. The installer must observe both these and any

other local regulations. This manual does not in any

way substitute the applicable regulations.

The product must be connected to a smoke exhaust

system which ensures that the smoke produced by

combustion is expelled in complete safety.

Before positioning the appliance, the installer must

check that the flue is suitable.

SMOKE DUCT, FLUE

The smoke duct

(which connects the combustion

chamber smoke outlet with the flue inlet)

chamber smoke outlet with the flue inlet) and the flue

itself must, among other regulatory requirements,

generally:

• receive the outlet from a single product only

(outlets of more than one product together are

not allowed)*; specific regulations apply in certain

countries, therefore the installer must ensure that

the local regulations have been observed;

• be installed vertically for the most part;

• have no downward sloping sections;

• preferably have a round internal cross-section and

nevertheless with a ratio between the sides below

1.5;

• end at roof level with a proper chimney pot: the

flue may not discharge directly on the wall or into

an enclosed space, even if the space in question

opens onto the sky;

• be made of material rated fire reaction class A1 per

UNI EN 13501 or analogous national regulations;

• be appropriately certified, with a suitable chimney

plate if made of metal;

• maintain the same cross-section throughout: it

may only vary immediately after the outlet, not

along the flue.

THE SMOKE DUCT

In addition to the general requirements for the fume

duct and the flue, the fume duct

• may not be made of flexible metal material;

• must be insulated if routed through unheated

areas or outside;

• must not be routed through rooms where the

installation of combustion heat generators is

prohibited, or that are subject to potential fire, or

that cannot be inspected;

• must enable the recovery of soot and be open for

inspection;

• generally speaking, must not have more than 3

bends with a 90° maximum angle; the technician

who sizes them must assess the situation;

• generally speaking, if there is a horizontal section,

it can have a maximum/average length of 3 metres,

depending on the draught. Nonetheless, take into

account that long sections favour dirt build-up and

are harder to keep clean; the technician who sizes

the pipes must assess the situation.

Avoid infiltration of condensate water

through the flue. If necessary, mount an

anti-condensate ring – ask your chimney

sweeper for details.

Damage caused by condensate water is

not covered by the warranty.

In some nations, installations with multiple

flues are permitted under certain conditions.

Depending on regional regulations,

additional safety systems are necessary in

case of connection to multiple flues. Your

chimney sweeper/technician will be able to

provide further details.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Edilkamin Cherie 11 Evo ATC Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Edilkamin Cherie 11 Evo ATC

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info