Bedienungsanleitung Edilkamin Daisy (Seite 8 von 28) (Englisch)

810907

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

ENGLISH

The Circulator

“Pushes” water toward the heating system.

Closed expansion tank

“absorbs” the variations in the volume of water contained

inside the boiler-stove due to the heating effect.

Aheating technician must evaluate the need to add a se-

cond tank to the existing one, depending on total amount

of water in the system.

Gear motor

This activates the screw allowing the transport of the pel-

lets from the hopper to the chamber.

Manometer

Located in the upper part under the top grill (B -fig. 2), it

allows water pressure to be read. When the thermo stove is

running, the recommended pressure is 1,5 bar.

Drain tap

Positioned on the back of the thermo stove, low down. It

must be opened if the water the unit contains needs to be

drained.

Venting valve (V)

Located in the upper part under the top grill (see fig. 2), it

allows for any air present during the loading of the water

into the stove to be bled off.

Smoke thermocouple

on the smoke outlet. It reads the smoke temperature. It

regulates the ignition stage and shuts the boiler-fireplace

down if the temperature is too high or too low.

Feed Screw safety thermostat

Placed near the pellet hopper. It disconnects the electrical

supply to the gear motor if the temperature detected is too

high.

Water temperature detector

It reads the water temperature in the boiler and sends the

circuit board information for pump management and boiler

power modulation.

If the temperature is too high, it starts a shutdown.

Water overheating safety thermostat

detects the water temperature in the thermo-stoves. If this

is too high, it triggers the shutdown process by disconnec-

ting the electrical supply to the gear motor. If the thermo-

stat has triggered a reaction, it must be reset by means of

the red emergency button at the left side of the stove (A

- fig. 1).

Overpressure valve

Upon reaching the pressure stipulated on the plate, the

system is triggered to discharge the water and consequen-

tly the water must be topped up.

WARNING!!!! remember to carry out the connection with

the sewage system.

Electric coil

It sets off of the combustion of the pellets and it remains lit

until the flame has been ignited. This component is subject

to wear.

Pressure switch

Positioned in the fume-aspiration area, it is triggered in the

case of a depression in the fumes circuit (e.g. obstructed

flue) and interrupts the movement of the pellets. It blocks

pellet loading causing the stove to go out.

Vacuum gauge (electronic pressure sensor):

positioned on the smoke extractor, which detects the vacu-

um value (compared to the installation environment) in the

combustion chamber.

Tank safety thermostat:

Located on the system that loads the pellets from the

hopper.

Trips when the temperature inside the boiler-stove is too

high.

It stops pellet loading, causing the boiler-stove to go out.

• COMPONENTS - SAFETY AND DETECTION DEVICES

N.B.:

IF THE BOILER-STOVE BLOCKS, THE REASON WILL APPEAR ON THE DISPLAY AND THIS WILL BE

SAVED.

fig. 1

fig. 2

GENERAL INFORMATION

INSTALLER

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Edilkamin Daisy Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Edilkamin Daisy

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info