Bedienungsanleitung Edilkamin Daisy (Seite 12 von 28) (Englisch)

810907

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

ENGLISH

- Must have a vertical expansion of not less than 30 cm.

After which the pipe can continue horizontally with a gra-

dient that fosters the flow of water.

- The diameter of the pipe must be at least one measure-

ment larger than the nominal measurement of the dischar-

ge of the valve.

The end of the pipe must discharge into the sewer system.

IT IS FORBIDDEN TO SHUT OFF THE DISCHARGE

• Verify that the hydraulic system is correctly installed and

is equipped with an expansion tank that is sufficiently large

to guarantee safety.

The presence of a tank within the boiler-stove

does NOT guarantee appropriate protection

from thermal expansion occurring in the who-

le system.

There fore the installer must assess whether

an additional expansion tank is needed, de-

pending on the type of system installed.

• Fill the system using the filling tap (it is recommended

not to exceed a pressure of 1,5 bar).

When filling, ‘bleed’ the pump and the relief tap.

• It is possible that it will be necessary to open the vent du-

ring the initial days of operation to release air in the system.

PLUMBING CONNECTION

The plumbing connection depends on the type of system.

However, there are some “common rules”:

• The plumbing connection must be carried out by qua-

lified personnel who can issue documentation declaring

correct installation conforming to current law in each count-

ry (for example, in Italy according to Ministerial Decree

37/2008 and standard UNI 10412-2)

• The plumbing system must operate at a pressure betwe-

en 1 and 1.5-2 bar on a hot closed-vessel circuit.

Note: DO NOT install the stove in place of, for example, a

thermocooker installed with an open vessel without an ade-

quate expansion system making it a closed vessel.

• The separation of the primary from the secondary circuit

is ideal and, in some countries, it is also mandatory in case

of the installation of a heating plant (for example, in Italy,

the reference is the Circular from ISPESL, now INAIL, of

April 2011).

This separation is easily carried out using KIT A2 from

Edilkamin.

• The presence of a puffer (inertial storage tank) is recom-

mended but not mandatory. Its presence has the advan-

tage of freeing the stove from “sudden” demands from

the heating system and allowing the integration of other

heat sources. It reduces consumption and increases the

efficiency of the system.

• The hot water exiting from the output of the stove must

be “directed” differently depending on the objective (hea-

ting, radiators, exchanger, whether or not there is a puffer,

etc.)

• The return temperature of the water at the stove must be

at least 50-55°C to avoid condensation. Depending on the

system, the installer must determine if anti-condensation

valves or pumps are necessary.

• A puffer (inertial storage tank) is needed for heating any

installed low-temperature under-floor heating panels accor-

ding to the guidelines of the manufacturer of the panels.

The under-floor panels should not receive water directly

from the stove.

• The material used in the circuit must be suitable to

withstand any overheating.

• The discharge of the safety valve must be accessible

and visible.

The discharge water must be channelled into a vertical

pipe using a funnel with backflow air intakes, appropriately

spaced from the discharge point.

The conveying pipe must have the following characteri-

stics:

- Must not originate more than 50 cm from the discharge of

the valve and must be positioned in the same room where

the KIT is positioned.

• Based on the type of water, the installer must determine

whether or not to use conditioned products according to

UNI 8065-1989 (treatment of water in heating systems for

civil use).

• Due to the small diameter of the pipes themselves, direct

connection to the radiators prevents normal operation.

• Below are several diagrams of “typical” installations

provided by Edilkamin.

The accessories for their implementation are available from

your dealer.

fig. 2

INSTALLATION

INSTALLER

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Edilkamin Daisy Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Edilkamin Daisy

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info