Bedienungsanleitung Edilkamin Daisy (Seite 19 von 28) (Englisch)

810907

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

ENGLISH

Filling the cochlea.

The first time you use the product, or should the tank

be completely emptied of pellets, to fill the coclea press

both keys “+” and “–” on the remote control at the

same time, holding for a few seconds. As you release

the keys, the display should show the wording “LOAD”.

This should be carried out before ignition if the boiler-

stove has stopped due to having run out of pellets,

at the end of operation to empty the combustion pot

before turning.

It is quite normal for some pellets to remain, that the

cochlea cannot suction.

Automatic igniting.

With the boiler-stove on stand-by, press and hold the

key , on the remote control for 2 seconds. This will

start-up the ignition procedure, showing the wording

“START”.

At the same time, a countdown in seconds begins (from

1020 to 0). Ignition is not at a preset time, however: its

duration is automatically shortened if the board reports

that certain tests have been passed. The flame appears

after about 5 minutes.

Manual igniting.

Temperatures of below 3°C will not allow the electrical

resistance to heat sufficiently. In this case, or should the

resistance be temporarily out of action, Diavolina® type

fire-starters can be used.

Insert a piece of lit Diavolina into the combustion cham-

ber, close the door and press the remote control.

OUTPUT TEMPERATURE ADJUSTMENT:

The SET output temperature can be altered by pressing

the keys +/-.

ENVIRONMENT TEMPERATURE ADJUSTMENT:

By activating the COMFORT CLIMA (CAT) function with

the +/- keys, the remote control device can be used

as a mobile thermostat/chronothermostat: place it in

the home in a position where the set temperature is

desired, select COMFORT CLIMA with the menu key;

the display will show the environmental temperature

(AIR) and the desired environmental temperature (SET);

adjust the desired temperature with the +/- keys and

the remote control dev¬ice will automatically send the

request to the stove.

Turning off

With the boiler-stove running, press and hold the key

rom the remote control for 2 seconds. The turn-

off procedure will begin, showing a countdown on the

display from 9 to 0 (for a total of 10 minutes).

The turn-off phase involves:

• Interruption of pellet supply

• Smoke expulsion motor

• Circulator

Unless otherwise set, managed by the CAT.

Never pull the plug out whilst the device is still in the

process of turning off.

N.B.: the circulator will continue turning for 5 - 10 minu-

tes after switching off.

OPERATIONS THAT CAN ONLY BE CARRIED OUT

BY REMOTE CONTROL

Clock regulation

Press and hold the key “M” for 2 seconds to access the

“Clock” menu. This allows you to set the internal electronic

board

clock. By then pressing the key “M”, the following data appe-

ars in sequence and can be regulated:

day, month, year, hour, minutes, day of the week.

The wording “SAVE??” will appear for confirmation with “M”.

This will allow you to check that the operations performed

are correct, prior to completion (the wording “SAVE” will then

be shown on the display).

Operations for switching on, switching off and changing the

SET temperature can be carried out by means of the red

emergen¬cy button placed on the back of the boiler-stove

(see page 50).

Weekly timer

Press and hold the “M” key on the remote control for 2

seconds. This turns on the clock regulation and by pressing

the ‘+’

key, the weekly timer function is accessed, with the display

showing the description “PROGRAMM ON/OFF”.

This function allows you to select the type of programming,

which allows a maximum of three ignitions to be set.

As you confirm the display with the key “M”, one of the fol-

lowing options will appear:

NO PROG. (no programme set)

DAILY PROGRAM (single programme for every day of the

week)

WEEKLY PROGRAM. (specific programme for each day

individually)

Use the “+” and “–” keys to switch between programmes.

Confirming by pressing the “M” key “DAILY PROGRAM.” and

pressing the “+” key, the choice of the number of program-

mes (ignition/extinguishing) per day can be made.

Use the “DAILY PROGRAM” to set identical programme/s for

every day of the week.

By then pressing the “+” key, the following can be seen:

- Prog. no.

- 1st prog. (one turn on and one turn off per day), 2nd prog.

(identical), 3rd prog. (identical)

Use the “–” key to show in reverse order.

If the 1st programme is selected, the turn on time is shown.

The display shows: 1 “ON” at 10 Use the “+” and “–” key

to change the hour. Confirm with the “M” key (All 1 On/Hour

10).

The display shows: 1 “ON” at 30 Use the “+” and “–” key to

change the minutes. Confirm with the “M” key (1 Off min).

The same applies for the turn-off time to be set and for

subsequent turning on and off.

Confirm by pressing “M” and the wording “SAVE??” will

appear on the display.y.

When confirming ”WEEKLY PROGRAM”, you will need to

choose the day to which the programming is to apply:

7 Sat; Progr.1; 1 Mon ; 2 Tues; 3 Wed; 4 Thurs; 5 Fri; 6 Sa;

Once the day is set, use the keys “+” and “+” and con-

firm by pushing the “M” key to choose 1 to 3 ignitions, to

programme in the same way as for the “DAILY PROGRAM”,

choosing whether or not to enable a programme for each

day of the week, and if so choose the number of interven-

tions and at what times.

Should you make an error during programming, you can lea-

ve the programme without saving. As you press a key, ,

the display will show the word “no SAVE”.

USER INSTRUCTIONS

USER

Edilkamin Daisy Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Edilkamin Daisy

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info