Bedienungsanleitung Edilkamin Dame (Seite 16 von 24) (Englisch)

810829

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

- 16 -

ENGLISH

INSTRUCTIONS FOR USE

Filling the cochlea.

The rst time you use the product, or should the tank be com-

pletely emptied of pellets, to ll the coclea press both keys “+”

and “–” on the remote control at the same time, holding for a

few seconds. As you release the keys, the display should show

the wording “LOAD”. This should be carried out before igni-

tion if the stove has stopped due to having run out of pellets,

at the end of operation to empty the combustion pot before

turning.

It is quite normal for some pellets to remain, that the cochlea

cannot suction.

Automatic igniting.

With the stove on stand-by, press and hold the key , on the

remote control for 2 seconds. This will start-up the

ignition procedure, showing the wording “START”. At the

same time, a countdown in seconds begins (from 1020 to 0).

Ignition is not at a preset time, however: its duration is automa-

tically shortened if the board reports that certain tests have

been passed. The ame appears after about 5 minutes.

Manual igniting.

Temperatures of below 3°C will not allow the electrical resi-

stance to heat sufciently. In this case, or should the

resistance be temporarily out of action, Diavolina® type -

re-starters can be used.

Insert a piece of lit Diavolina into the combustion chamber,

close the door and press the remote control.

POWER REGULATION

• Remote control manual operation

With the stove working, press the key “M” on the remote con-

trol once. The display will show the word “POWER P”.

(specifying the power at which the insert is working). Press the

keys “+” or “–” to increase or decrease the insert’s

working power (from “POWER P1” to “POWER P3”).

• Remote control automatic operation

Press key “A” to switch to automatic operation, adjusting the

temperature desired for the room (use the “+” and “–” keys

to set the temperature from 5°C to 35°C, and the stove will

regulate working power required to reach the temperature set.

If a temperature below that of the room is set, the insert will

stay on “POWER P1”.

Turning off

With the stove running, press and hold the key rom the re-

mote control for 2 seconds. The turn-off procedure will begin,

showing a countdown on the display from 9 to 0 (for a total of

10 minutes).

The turn-off phase involves:

• Interruption of pellet supply

• Maximum ventilation

• Smoke expulsion motor

Never pull the plug out whilst the device is still in the process

of turning off.

OPERATIONS THAT CAN ONLY BE CARRIED OUT BY

REMOTE CONTROL

Clock regulation

Press and hold the key “M” for 2 seconds to access the “Clock”

menu. This allows you to set the internal electronic board

clock. By then pressing the key “M”, the following data appe-

ars in sequence and can be regulated:

day, month, year, hour, minutes, day of the week.

The wording “SAVE??” will appear for conrmation with “M”.

This will allow you to check that the operations performed are

correct, prior to completion (the wording “SAVE” will then be

shown on the display).

Operations for switching on, switching off and regulating

power can be carried out by means of the red emergency button

placed on the back of the stove (see page 47).

Weekly timer

Press and hold the “M” key on the remote control for 2 se-

conds. This turns on the clock regulation and by pressing the

‘+’

key, the weekly timer function is accessed, with the display

showing the description “PROGRAMM ON/OFF”.

This function allows you to select the type of programming,

which allows a maximum of three ignitions to be set.

As you conrm the display with the key “M”, one of the fol-

lowing options will appear:

NO PROG. (no programme set)

DAILY PROGRAM (single programme for every day of the

week)

WEEKLY PROGRAM. (specic programme for each day

individually)

Use the “+” and “–” keys to switch between programmes.

Conrming by pressing the “M” key “DAILY PROGRAM.”

and pressing the “+” key, the choice of the number of program-

mes (ignition/extinguishing) per day can be made.

Use the “DAILY PROGRAM” to set identical programme/s for

every day of the week.

By then pressing the “+” key, the following can be seen:

- Prog. no.

- 1st prog. (one turn on and one turn off per day), 2nd prog.

(identical), 3rd prog. (identical)

Use the “–” key to show in reverse order.

If the 1st programme is selected, the turn on time is shown.

The display shows: 1 “ON” at 10 Use the “+” and “–” key to

change the hour. Conrm with the “M” key (All 1 On/Hour

10).

The display shows: 1 “ON” at 30 Use the “+” and “–” key to

change the minutes. Conrm with the “M” key (1 Off min).

The same applies for the turn-off time to be set and for subse-

quent turning on and off.

Conrm by pressing “M” and the wording “SAVE??” will

appear on the display.y.

When conrming ”WEEKLY PROGRAM”, you will need to

choose the day to which the programming is to apply:

7 Sat; Progr.1; 1 Mon ; 2 Tues; 3 Wed; 4 Thurs; 5 Fri; 6 Sa;

Once the day is set, use the keys “+” and “+” and conrm by

pushing the “M” key to choose 1 to 3 ignitions, to programme

in the same way as for the “DAILY PROGRAM”, choosing

whether or not to enable a programme for each day of the

week, and if so choose the number of interventions and at what

times.

Should you make an error during programming, you can leave

the programme without saving. As you press a key, , the

display will show the word “no SAVE”.

Edilkamin Dame Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Edilkamin Dame

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info