Bedienungsanleitung Edilkamin Dania Air Tight C Plus (Seite 11 von 60) (Englisch)

810763

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

ITALIANO

FLUE SYSTEM

(fumes duct, flue and chimney pot)

This chapter has been drawn up pursuant to European

regulations EN 13384, EN 1443, EN 1856 and EN

1457. The installer must observe both these and any

other local regulations. This manual does not in any

way substitute such regulations.

The product must be connected to a flue system which

ensures that the fumes produced by combustion are

expelled in complete safety.

Before positioning the appliance, the installer must

check that the flue is suitable.

FUMES DUCT, FLUE

The fumes duct (which connects the combustion

chamber smoke outlet with the flue) and the flue itself

must, among other regulatory requirements:

• receive the fumes from a single product (the outlets

of multiple appliances may not be conveyed into

a single flue)

• be routed vertically for the most part

• have no downwards sloping sections

• preferably have a circular internal cross section, or

with a ratio of the sides of less than 1.5

• terminate at roof level with a proper chimney pot:

the flue may not discharge directly on the wall

or into an enclosed space, even if the space in

question is open to the sky

• be made of material with rated fire reaction class

A1 as per UNI EN 13501 or analogous national

regulations

• be certified, with a chimney plate if metal

• be of uniform cross section or vary in cross section

only immediately after the outlet, not at some

midpoint of its length.

THE FUMES DUCT

• Further to the general prescriptions for the fumes

duct and flue, the fumes duct:

• may not be made of flexible metal material

• must be insulated, if routed through unheated

areas or outdoors

• must not be routed through rooms where the

installation of combustion heat generators is

prohibited or there is risk of fire, or that cannot be

inspected

• must enable the recovery of soot and be open for

inspection

• must have a maximum of 3 bends with a maximum

angle of 90°

• if there is a horizontal section, it can have a

maximum length of no more than 3 metres,

depending on the draw. Note, in any case, that

long sections encourage the accumulation of dirt

and are harder to keep clean.

THE FLUE:

Further to the general prescriptions for the smoke duct

and flue, the flue:

• must only be used for discharging fumes

• must be correctly sized to satisfy the requirements

for fume discharging (EN 13384-1)

• should preferably be insulated, in steel with a

circular internal section. If rectangular, the corners

must have a radius of not less than 20 mm, with

aratio of the internal dimensions of <1.5

• must normally be at least 1.5 metres in vertical

length

• must have a constant cross section

• must be waterproof and thermally insulated to

ensure a good draw

• preferably provide a collection chamber for

unburnt residues and condensates

• if pre-existing, must be clean, to prevent fire

hazards

• in general, we recommend fitting a tube inside the

existing masonry chimney if its diameter is greater

than 150 mm.

INSTALLATION

INSTRUCTIONS FOR THE SMOKE

DISCHARGE WITH OR WITHOUT

CONCENTRIC PIPE

INSTALLER

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Edilkamin Dania Air Tight C Plus Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Edilkamin Dania Air Tight C Plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info