Bedienungsanleitung Edilkamin Demy (Seite 18 von 28) (Englisch)

810764

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

- 18 -

ENGLISH

Changing pellet loading (with self-regulation deactivated)

By pressing the “M” button on the remote control for two sec-

onds and scrolling the display with the “+” and “-” buttons, you

will come to the description “ADJ-PELLET (CAT)”.

If automatic regulation is ON in the parameters, this setting of

manual ADJ is NOT possible.

When this is conrmed the display reads “ADJ-PELLET ;

ADJ-DRAUGHT and RADIO MENU” (CAT). The pellet drop

can be adjusted manually by changing the capacity in percenta-

ge terms (+/- 30 %).

By conrming this function with the menu key, you can access

the function to adjust pellet loading. By decreasing the

value set, pellet loading is decreased. By increasing the value

set, pellet loading increases. This function is useful if

changing the pellet type for which the stove has been calibrated

and loading therefore needs correcting.

Should this correction not sufce, contact the Edilkamin-autho-

rised Dealer, to establish the new operating axis.

Notes on ame variability

Flame status may vary depending on the type of pellet used,

in addition to normal solid fuel ame variability and regular

combustion chamber cleaning carried out automatically by the

boiler.

(N.B.: which does NOT replace necessary cold suction by the

user prior to ignition).

RESERVE WARNING

The stove is tted with an electronic function that detects the

residual quantity of pellets in the tank.

The detection system is integrated into the electronic board,

allowing you to see how many hours and kg are left until

pellet exhaustion, at all times. For correct system function, it is

important that the following procedure is followed during the

rst ignition (by the Dealer).

This provides a reference indicator. Greater precision is

obtained by regularly zeroing the system before lling it again.

Edilkamin does not accept any responsibility for differences

from what is indicated (which may be due to external factors).

Pellet reserve system

Before enabling the system, you need to load a sack of pellets

into the tank and use the stove until the loaded

fuel has run out. This allows for a short system road test.

After this, the tank can be lled completely and the stove

started up.

When running, at the time at which a whole 15 kg sack of pel-

lets can be loaded, the display will show the word

“Reserve” ashing.

At this point, after having poured in a sack of pellets, you need

to ‘inform’ the memory that you have loaded 15 kg.

To do so, proceed as follows:

1. press the “M” key (for approximately 3-4 seconds) until the

word “Clock” appears.

2. press the “+” key until the word “Reserve pellet” appears.

3. press the “M” key until the following screen appears,

then use the “+” key to take the gure (*) to the value equal to

the Kg of pellets loaded (15 kg in the above example).

4. press the “M” key to conrm

5. press the key to exit.

After having completed the above procedure, after having con-

sumed the 15 kg, the wording “Reserve” will appear

ashing at intervals. After which the operation must be repea-

ted, from point 1 to point 5.

SIMPLIFIED LIGHTING BUTTON

If the remote control device does not work, you can carry out

the basic functions by means of a red emergency button placed

on the back of the stove (see Fig. 1).

Push this button once or more times to activate the required

function:

1. STOVE OFF

by pressing the red button for 2 seconds this turns on.

1 beep conrms the command

2. STOVE ON

by pressing the red button for 2 seconds this turns off.

1 beep conrms the command

3. WITH STOVE IN STAND-BY MODE

pressing the red button for 5 seconds, the stove lights with

wood using the pellets (LIGHT WOOD function) 3 beeps con-

rm the command.

Kg remaining in tank Kg caricati

INSTRUCTIONS FOR USE

g. 1

simplied lighting

button

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Edilkamin Demy Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Edilkamin Demy

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info