Bedienungsanleitung Edilkamin Double (Seite 20 von 62) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

810848

Zoom out

Zoom in

Vorherige Seite

1/62

Nächste Seite

ENGLISH

Igniting with cold hearth

1 Check that the ash bed is not too high.

Maximum height: 5 cm below the edge of

the panel.

If the ash bed becomes too high, there is a

danger that when opening the panel to add

wood, fragments of coal may fall out of the

hearth.

2. Completely pull the regulating control

(fig 7 - page 14) of the air valve in the

“switch on” position. Air for fuelling will

flow intensely to the wood in the hearth, to

rapidly reach high heating power.

3. The wood must be placed in the hearth

without excessively crowding it. Place an

igniter between the wood logs, and ignite.

The igniters are practical aids which ignite

only if placed underneath or in front of

wood waste. Attention: very large wood

logs do not ignite properly in a cold hearth

and free noxious gasses.

Never use material such as petrol, alcohol

and similar to ignite the hearth!

4. At this point, close the hearths panel

and supervise for a few minutes. Should the

fire go out, slowly open the panel, allocate

another igniter between the wood logs and

re-ignite.

5. Should the fire not require further

addition of wood, the moment the same

fire is exhausted, push the regulating lever

(fig. 7 - page 14) of the air valve in the

“maintain fire” position. Do not carry out

such regulation during the fuelling phase

and the release of noxious gasses, in

that, when the lever is in the maintain fire

position, the air flow for fuelling results

completely blocked. In case of sudden

oxygen flow (for ex. due to the opening of

the hearths panel) the “gasses still present”

in the hearth and in the eventual heat

recovery surfaces, may react violently with

said atmospheric incoming oxygen

Power supply with hot hearth

1 Pull the regulating control (fig 7 - page

14) of the air valve in the “switch on”

position and add the required amount

of wood in the hearth, placing it on the

existing coal. In this way, the wood will heat

up with the consequent expulsion of steam

and of the contained humidity. This leads

to a decrease of the temperature inside the

hearth. The volatile substances let out at

this point by the fuelling material require a

sufficient air flow, so that this critical phase

can be rapidly carried out and the required

temperature can be reached for the correct

fuelling.

A further suggestion:

For the initial ignition of the hearth, always

use the smaller wood logs. These rapidly

burn and therefore bring the hearth to

the right temperature in less time. Use the

larger logs of wood to re-power the hearth.

Certain types of wood briquettes inflate

once they are in the hearth, meaning they

stretch under the heat and increase in

volume. Always place the wood well inside

the hearth, nearly touching the rear wall of

the same, so that should it slide, it does not

fall in the panel.

USE INSTRUCTIONS

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Edilkamin Double Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info