Bedienungsanleitung Edilkamin EK130 (Seite 25 von 32) (Englisch)

810845

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

INSTALLER

IMPORTANT! BEFORE PROCEEDING WITH

IGNITION, CAREFULLY READ ALL THE

INSTRUCTIONS AND PRECAUTIONS SHOWN IN

THIS BOOKLET.

First ignition could be difficult because of

the possible presence of air in the gas pipe.

In case of short ignition or switch-off of the

appliance, wait at least 5 minutes before repea-

ting the ignition operation.

When first ignited, the Appliance may give

off a bad smell or vapours. This is entirely

normal. The best thing is to ventilate the premi-

ses adequately.

After igniting, allow the appliance to operate

for about ten minutes at maximum output,

to permit adequate heating.

If the appliance is to be used for short

periods of time, it is best not to switch it off

but rather leave it with the pilot light on. This

way, the formation of condensation is prevented

in the pipes that reach the flue and which, in the

long term could cause hearth corrosion.

REMOTE CONTROL UNIT

Ignition

• Open the gas supply tap.

• Press the switch (5) of the gas valve in “ I “ position.

• Make sure the knob (7) of the manual operation

mechanism is positioned on “ON”.

• Press the keys “OFF” and “triangle UP” of the

remote control at the same time.

• An acoustic signal will indicate the start of the start

sequence. The electronic system checks correct gas

flow and ignites the main burner (these operations

could take up to 20 seconds). After burner ignition,

the flame automatically positions on maximum.

If the pilot flame goes out, wait at least five

minutes before repeating the described ope-

ration. During the start phase, the knob of the

manual operation mechanism must be positio-

ned on “ON”.

Operation

Setting the electronic code for RF remote con-

trols (with or without display).

A code is selected automatically between 65000 ran-

dom codes available. The receiver (at the edge of

the chimney) must know the remote control code:

Expected sequence:

- Press and hold the RESET button of the receiver in

the fireplace until you hear two (2) beeps: the first is

short and the second is long. After the second beep,

release the RESET button.

- Within the next 20 seconds, press the button (small

flame) on the remote until you hear two short beeps,

which further confirm the correct setup code. If you

hear one long beep, the acquisition sequence code

failed or the wiring is incorrect.

This setting is performed only once and is

not required after changing the batteries on

the remote or receiver.

Once turned on, you can choose the power level of

the Device using the remote control. Press the remo-

te button "triangle DOWN" to reduce the intensity of

the flame and press "triangle UP" to raise it.

Once the Appliance has been switched on,

the Manufacturer suggests leaving it run-

ning for 10 minutes at max output, before making

any adjustments.

At minimum, the burner remains off, leaving on only

the pilot flame.

From minimum position, the output can be turned up

without repeating the ignition operation.

MAX

OFF

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Edilkamin EK130 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Edilkamin EK130

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info