Bedienungsanleitung Edilkamin EKB60 (Seite 25 von 28) (Englisch)

810711

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

CUSTOMER SERVICE

ROUTINE MAINTENANCE

Any type of job done on the appliance must

only be performed by a qualified technician

and AT LEAST ONCE A YEAR.

Cleaning the hearth

- Delicately brush and reposition all the ceramic ele-

ments and if necessary change the damaged ele-

ments.

- Brush the gas outlet holes (flames) on the burner.

Check the burner and for any gas leaks

- Make sure the burner is clean and check its inte-

grity.

- Check the gas outlet safety system. If necessary

adjust the burner. The technician must also check

the regulation pressure at the burner inlet.

- Check the existence of any gas leaks in the

system.

- Proceed to check the ignition.

Checking the fireplace.

Check the correct operation of the fume exhaust and

combustion air suction pipes.

The Appliance must only be used for the

purpose intended by the Manufacturer and

for which it was expressly designed and made.

The Manufacturer disclaims any contractual and

non-contractual liability for injuries and damage

caused to people, animals or things as a result of

the wrong installation, regulation, maintenance

or improper use of the Appliance.

Spare parts and/or technical jobs require the

prior identification of the model of appliance

to which they refer.

The tampering, removal, lack of Technical Plate,

etc., will not allow the correct identification of the

product and will make installation operations and

subsequent maintenance jobs difficult.

FAULTS AND SOLUTIONS

THE PILOT LIGHT DOES NOT IGNITE OR WORK

- Make sure the pilot burner flame is of the correct

size for the type of gas used.

- The flame must converge on the thermocouple sen-

sor.

- Make sure the pilot flame has been regulated.

THE MAIN BURNER DOES NOT WORK

- Make sure the pressure and volume of the gas sup-

ply to the appliance is adequate. Check by connec-

ting a pressure gauge to the gas pressure point on

the gas valve.

- Ignite the appliance and allow it to operate at maxi-

mum output. Close all the other gas appliances in

the house and calculate the quantity of fuel burnt by

reading the meter.

Before arranging any element, make sure

burner combustion is correct. The flame

must be uniform over the entire burner surface.

THE PILOT FLAME DOES NOT IGNITE OR DOES

NOT STAY ON

- Make sure the gas tap is open on the appliance

and on the meter/tank.

- Keep the control knob pressed for at least 20

seconds after the ignition of the pilot flame to ensure

operation of the thermocouple safety valve.

- Make sure the injector of the pilot burner is not

blocked by dust or dirt.

- Make sure the thermocouple has not been dama-

ged during transport. This electromagnetic device is

in fact very delicate.

- In case of an LPG fuelled system, make sure there

is gas in the tank.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Edilkamin EKB60 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Edilkamin EKB60

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info